Jump to content
SAU Community

Recommended Posts

if they had the window trims removed like c34s it would look a lot sharper... and i gotta say, the sharp, boxy look of the c34's is a lot tougher, hey. M35's are sleek, for sure. but they look like mercedes meets chrysler voyager.

Looks like an very unforgiving ride-height, hope its bagged, looks nice. Wouldnt buy one, but i'd do skids in it for a day.

Yeah it's nice having Techo's sig pic so close, why would you got for the M35, when you could have something as angry looking as Techo's!!! That body kit is the only way to make a S2 look farkin hawt!

haha i was doing the same thing, scrolling up and down and comparing them! that is EXACTLY what i mean. LOVE the older-school angles of the C34...

  • 2 weeks later...
Is anyone going to be bringing these in as low volume imports?

Or do they miss out under the new legislation??

If they are available anyone know what kind of Cash they would sell for??

I'd be tempted to haggle this one down (as I'm in NZ), high as K's, but still, how stuffed can it be. Then again its still about twice what I paid for a S1, so is it worth it.

Its the real-deal 400Nm of torque one though.

20148830_full.jpg

http://www.trademe.co.nz/Trade-Me-Motors/C...on-49203407.htm

Edited by Spammeoff
I'd be tempted to haggle this one down (as I'm in NZ), high as K's, but still, how stuffed can it be. Then again its still about twice what I paid for a S1, so is it worth it.

Its the real-deal 400Nm of torque one though.

20148830_full.jpg

http://www.trademe.co.nz/Trade-Me-Motors/C...on-49203407.htm

OMFG!! $16,500!!!!!! Gawd damn, wonder how much it would be to buy it and ship it over here to AU?

Damm... has anyone got the low volume compliance for them in OZ that would be willing to do the compliance??

Their working on it

About 6 months away

http://www.skylinesaustralia.com/forums/in...howtopic=122677

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...