Jump to content
SAU Community

Recommended Posts

Hey people only new to SAU, we have organised a meet and small cruise this Tuesday night.

Start Harrys Diner 07:30 depart 08:30

Off to riverside and then Cootha.

Just a change from the usual Thursday, Saturday and Sunday cruises.

Come say hello will be in a white R33.

Link to comment
https://www.sau.com.au/forums/topic/125482-tuesday-night-meet-and-cruise/
Share on other sites

do'h, i'm working 4pm - midnight on thursday... looks like i'm out :)

The meet is on TUESDAY nite, its just a change from the Thursday nite out when you get all the idiots attracting the cops.

And for people who normally work Thursday nights.

Edited by subzeroR33
You keep saying north side and places I have no idear about :thumbsup:

I am from Ipswich heh I live where all the rev heads are..

What booosted 33 said,

Newmarket rd Windsor

it will be in ur street directory cant miss it..

Edited by subzeroR33
You keep saying north side and places I have no idear about ;)

I am from Ipswich heh I live where all the rev heads are..

we're not ALL revheads bish :dry:

i'm from ipswich too, cant say ive seen u around...(i use to own a black 33 with gold mags, cf bonnet)

oneday when the gtr's finished ill come to these cruises :D

i know where it is, if u wanna pick me up on the way i can show u :D

hey guys depending on work i might show up in my black r33 sounds good and not on a thurs nite which is also a plus

For some who cant make it to harrys, we will be at west end riverside about 9ish and will leave about 9:45 for cootha.

Edited by subzeroR33

Sorry Guys I took the wheels off my car today and found I needed to do some work I wasnt expecting

I will miss tonights drive but hopefully I can get to the next one :)http://i16.photobucket.com/albums/b33/Anni...4u/100_0491.jpg

Edited by MajorSick
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...