Jump to content
SAU Community

Recommended Posts

I know this is a skyline appreciation forum but i have always been open minded about cars. If the XR6t had been around when i bought my GTS25t i would have had a much more difficult time deciding on buying my skyline.

In the following link they say that with a couple of tweaks and some extra boost you get 252rwkw out of the XR6t. How tuff is that. Also they say that 300rwkw would be a "doddle", that will really put the wind up someone driving a HSV with 300 flywheel kw.....

http://www.fordforums.com/showthread.php?t...25&pagenumber=1

I think it is impressive that a local manufacturer has finally come up with a MODERN performance car. None of this single cam push rod junk but a really serious peice of gear. Mind you dont get me started on how the intercooler is plumbed because that really was a MAJOR COMPROMISE.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/
Share on other sites

bolting on a turbo doesn't instantly makes it a well refine sportcar as a skyline. but it does help the falcon street cred though. if u get a chance hurl one into a sweeper at the same rate as u would do in a skyline and see how much room there is left in ur undies. It's still a family car in the end.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230877
Share on other sites

Hungry 6 have you tried driving one????

It is more of a family car than a race car (skyline being a race car of course) as such it will weigh more.

I personally hate the way the intercooler/ inlet manifold/ turbo is piped because it is a compromise. BUT you cant argue with a family car that pulls 240kW running 6psi which is heavily detuned. Oh by the way can your car seat 4 people as comfortably as a XR6t???

I took one for a run and i was surprised at how the suspension combined with the traction control made the car stick under serious accelaration through some cornering. The sales person did get a bit edgy at times but i assured him that i was looking at upgrading from the GTS25t to a family car with some go (cough cough like hell i was).

They didnt JUST bolt on a turbo if you check the specs they also dropped the static compression ratio and did a lot of heat shielding among other things.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230969
Share on other sites

My mate works for the company that makes Ford's transmissions, and agrees the manual is at an end for torque handling, they have been leaning on it for years and keep asking to do what it was never designed to do, with this in mind the 5 spod doesnt do that bad a job.

He has worked primarily on the auto, and with him having driven my 32 GTST many times when im pissed and egging him on, he has a good idea what my car can do.

For the record the guy isnt full of BS, and claims despite the weight of the car, and saloon heritage, the development mules that he R & D flog my GTSt in accelaration, have great brakes, and handle great. He says with the handling you just have to be mindful the it is a production car with a pretty hefty kerb weight, so no brakes/heavy acceleration mid corner/ebtry to corner etc, be smooth and it can do the job. Hell he has driven the thing on great ocean road.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231153
Share on other sites

I've heard from a few sources that the XR6t has a boost limit of 7psi.

Once it hit's 7psi the ECU starts to pull back timing and then starts the boost cut - just like some R33 gts-t's hit at 12psi.

If this is true, it'd be a pain in the butt to go to a full ECU change on such a modern car for a few extra psi :D

They are nice cars though. Boss at work has a blue one... Nice......

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231353
Share on other sites

There was a good article in the last HPI comparing the XR6 Turbo to the Supra. They said "The closest thing to a Japanese car to come out of Australia. We can't praise the XR6T any more than that".

I think the guy doing the review was a little biased as he owns a Supra, but hey, what can you do?

The writer goes on about how the 2JZ-GTE is the greatest and most proven engine of all time, whereas the 240T still has to prove it's self. "The few players in the aftermarket who have tested the 240T engine have come away confused and frustrated with an uncooperative managment system, and intercooler/exhaust systems that are far from optimum".

Apparently the LPG spec rods are a must for a serious build-up.

They also said that the Ford doesn't like to be revved!

All in all though, I think Ford is onto a good thing. However, if I was looking for a sporty family car, I'd still by a WRX!

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232077
Share on other sites

OK

Firstly it is a 4ltr. Motors with large swept capacity dont need to rev much because the have bulk torque early on in the rev range where as my RB25DET needs to be revved to get any go out of it.

For a sporty family car i would think it is ideal because you get a large turbo six with auto. You can be as lazy as you want to be and you can seat 4 passengers with large arses comfortably.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232092
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Something to note, on an aftermarket turbo, it's quite possible to end up with the worst of both worlds, where on light throttle, there isn't enough force to open the BOV so you get small reversion and driveability issues, and with the venting to atmosphere, it dumps a lot of fuel on shifts. Realistically, dumping to atmosphere under power isn't a major driveability issues, compared to the issues of stalling from reversion. If you're getting up the throttle, then putting the clutch in, say on a shift up, but then don't release the clutch, yes, the engine can and will stall, but, just drive around it, and that's easy, let the clutch out in the next gear and the car rolling will keep it all running / going.who wants a hard hit of throttle and then to just let the motor idle anyway?   Main issue for driveability is blipping throttle and it wanting to stall, like when parking or trying to move in slow traffic.
    • As in they quoted one price, you mentioned the exhaust, and they promptly added $200 on top? Interesting.
    • Note that I'm not suggesting this is a great idea. Just saying that it is something that could be done to achieve a better outcome than the more shit ideas will provide.
    • I'd try removing it, connecting hoses and see if that helps. Depending on specs, it could actually be restricting the flow(it also might be helping).
    • Yes, that's a hybrid BOV. The adjustable spring load ones are about making teh pressure build up higher before venting, so you get a more agressive whoosh. That is not what I meant or what you want. By "restricting", I don't mean "keep it closed until the pressure is higher, then open it fully". I mean "open it as soon as it is required, but only have a small port area, so that the flow rate out of it is slowed down". The pressure will rise to be higher than a bigger ported BOV would provide, but it would do while it is venting. The idea is to slow down the rate at which the replacement eair is flowing past the AFM, to reduce the magnitude of the air flow signal peak, to reduce the amount of fuel that is added per revolution.
×
×
  • Create New...