Jump to content
SAU Community

Shell Optimax Vs Bp Ultimate

RB SANDY
 Share

Recommended Posts

SIKLINE Apprentice

SIKLINE

Posted
Posted
Can anybody comment on their experiences with these fuels.

heya, i have a r33 s2 and i find that opimax runs far better in my car....have done a lot of shopping around and yeah shell was best. but yeah most peolpe have have spoken too have said that they won't touch it coz of the dirty fuel episode. hasn't happened to me and thats all i put in

Sydneykid Grand Master

Sydneykid

Posted
Posted
Everyone knows this.

Explain why on multiple occassions Shell reads a lower oxygen rating and slower lap times then other PULP ? I think you might find, and correct me if I'm wrong with proof, that each company also adds there own special mixes too the fuel at the same refinery.

Or... ring a marine shop, and ask them what fuels they suggest you use and WHY.....

Depends on where the fuel supplied for testing was sourced from. The BP Ultimate that is used for circuit racing comes from the BP refinery at Quinanna in WA. Arguably the best refinery in Australia using the best Australian crude oil. The Shell is sourced from Clyde in NSW. The Catex/Ampol comes from Kurnell in NSW, etc etc

So if you are looking at testing done in Vic then they might be testing BP Ultimate from Kwinnana, but that isn’t what you get when you pull up at a servo in Melbourne. You get BP made at the Shell refinery in Geelong, there is no BP refinery in Vic.

If you don’t believe me drive out to the refinery and watch the tankers pull in and out, you will see all the different brands.

Which marine shop should I call? One in Melbourne will give me a different answer than one in Perth.

hey guys what do you thin about shell extream 100 RON with 5% ethonol?

Absolutely the best stuff currently available in volume.

Do a search for more info, “Sydneykid”, “Extreme” and “any date”

:( cheers ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...