Jump to content
SAU Community

Leaking Coolant

eMsta

By eMsta,
in Engines & Forced Induction

 Share

Recommended Posts

eMsta Grand Master

eMsta

Posted
Posted

Hi all,

I have a major problem (i think) with the car. Since the last service (2 fridays ago), the car has been running fine. But then today when I was coming back from a very long drive (180klms), I noticed that the temp needle was going up and then down a bit. I thought this was just normal, so I didnt bother with anything. But then later tonite, after I came back from my bros house (about 5 mins away), the needle went right up.

My dad and I opened the hood, and there was a horrible smell. We knew that it was due to leaking coolant or lack of coolant. The water pump looks to be intact, but below the engine, there was a lot of liquid. That means the coolant is leaking froms somewhere there. We have checked the pipes as well, everything seems to be ok. I dont know where else to look.

Do you guys know what I can look out for as the main culprits for the leakage? We have filled up the coolant reservoir and the radiator, with a mix of coolant and water. But its still leaking. I am thinking of taking it to GTAutos for them to have a look at it, but I would appreciate any advise/pointers that you guys can give me.

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/
Share on other sites
Craved Grand Master

Craved

Posted
Posted (edited)

coolant can come from

rear: turbo feed pipe that is behind the head, and is fed from the rear of the plenum. heater hoses

side: oil cooler, heater feed hoses, feed from thermo housing to the plenum. turbo water feed @ turbo

front: radiator hoses.

Edited by Craved
Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2338802
Share on other sites
Fry_33 Proficient

Fry_33

Posted
Posted

This could mean that your water pump needs replacing. Happened to my mates R33 and was told that there is a small hole that will leak water/coolant when your water pump has had it, nissan mae it this way as a warning sign. You can see it if you look hard from memory. He was also told that once it starts leaking it should be changed fairly soon as it won't last much longer.

If it is your water pump then arrange to get your timing belt changed at the same time if it's close to needing it.

Good luck with your vehicle man

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2338821
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted
This could mean that your water pump needs replacing. Happened to my mates R33 and was told that there is a small hole that will leak water/coolant when your water pump has had it, nissan mae it this way as a warning sign. You can see it if you look hard from memory. He was also told that once it starts leaking it should be changed fairly soon as it won't last much longer.

If it is your water pump then arrange to get your timing belt changed at the same time if it's close to needing it.

Good luck with your vehicle man

Thanks for the info bud - but I changed the water pump 5 months ago (the timing belt and all were also changed). I do see something that looks like a crack, but hte pump is completely dry on the outside - nevertheless, I will get Wayne and Jarrod to have a look at it again.

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2338830
Share on other sites
Craved Grand Master

Craved

Posted
Posted

passenger side in the middle ???

sounds like turbo's water feed :blush: bit fiddly to get to though

can be feed or return, banjo bolts at return at block, and the turbo for feed and return .. feed comes from a rubber hose from behind the head

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2338882
Share on other sites
Darius Explorer

Darius

Posted
Posted

First, if it is coming from the "middle" of your motor but cannot trace it back to a point source like a coolant hose, then it is likely your head gasket. Second, change your oil to make sure it does not look like chocolate milk. If it looks like chocolate milk, you have problems. It is either a cracked head or blown head gasket.

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2339071
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted

Thanks for the heads up guys.

Craved: Its on the drivers side (towards the middle) - so im guessing its got nothing to do with the turbo.

Darius: i have checked the oil - it seems to be ok. I had the car serviced just 2 fridays ago by RE Customs.

i might check with them to see if they noticed anything abnormal about the car when they did the service.

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2339106
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted

Update: Ok, we have found the culprit. Its one of the Cylinder wall plugs. Seems that the bastard has rusted, due to the improper coolant mix being used. Uh!!!!! Thank god its not a major problem like a blown gasket, but I believe that the repair work will take a long time!

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2339112
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted

Yep - by monday she will be back to running like a beast :blink:

(and probably need a good clean too)

I emailed wayne in the morning - and he said that things like this happen if the car has not been looked after well. Eitherway, he is gonna help me change it so im wrapped!

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2341368
Share on other sites
Craved Grand Master

Craved

Posted
Posted

lucky you cahnged the water pump previoulsy otherwise the same thing woulda happened to the fins on the inside of it.. rendering it useless.

are you getting them all replaced now? dont want it to rust through another one

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2341468
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted

Well, I have to get him to check it on monday. I could only see one that was rusted beyond recognition. Hopefully get the whole thing replaced. The waterpump is fine from what i can see.

Just hope it doesnt take a long time, cos i cant live with out the car :blink:

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2341537
Share on other sites
eMsta Grand Master

eMsta

Posted
  • Author
Posted

Just wondering, how long would it take to replace these welsh plugs? Do they have to extract the whole engine? I know the have to flush out the coolant before they do anything, but if they have to remove the whole engine - then im gonna be charged shit loads.

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2347913
Share on other sites
  • 4 months later...
eMsta Grand Master

eMsta

Posted
  • Author
Posted

just bumping my own old thread

Took it for a service today to RE Customs - got a call back from Ray, prognosis negative - yep damn welsh plugs are haunting my ass again!

Warranty wont take care of it. and it looks like im going to have to pay shit load to get that fixed....

damn damn welsh plugs :wave:

Link to comment
https://www.sau.com.au/forums/topic/126680-leaking-coolant/#findComment-2733281
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...