Jump to content
SAU Community

Recommended Posts

Hi , i heard that these japanese tuner has built a 800hp silvia S15 , a 650hp FD3S and a fast Evo but i cant find any pictures or informations about these workshop , the old net adress has removed , so i need help ...

can everyone post a few pics of them ?! please no videos , i know them :devil:

hope you can help me ... nice day ... bye

greetz . german JDM-Fan No.1 "CyberEvo"

Link to comment
https://www.sau.com.au/forums/topic/126842-garage-stillway/
Share on other sites

Hi Peter :(

I couldn't find the Stillway site either... but I have some pics of the Stillway Evo 7 in the 'Photo Diary' thread in this forum. I might have some other pics on my PC, I'll upload them tonight (AU time) if I find any more.

Link to comment
https://www.sau.com.au/forums/topic/126842-garage-stillway/#findComment-2343089
Share on other sites

they tuned my car, with impressive results. They have a good repuation, and rightfully so. However, they run a very simple operation, and that doesn't include a website (their old site was pretty much just a 'under construction' sign for as long as it was up).

if you want parts, check yahoo auctions - as they sell a lot of parts on there.

Edited by DaiOni
Link to comment
https://www.sau.com.au/forums/topic/126842-garage-stillway/#findComment-2354694
Share on other sites

No shit someone been watchin too mahy DVD's!

?????????????????????????????????????????????

You being a smart arse or serious?

Hi-octanes are the only DVD's I've watched as my friend has them. "IF" you were serious, they do a tour of japan and stillway wins because they just rock up and ask to film some hot cars and they tell them that they can TAKE the 900HP S15 or film the 600Hp RX7. Goes on to show the RX7 at what can only be described as warp speed on a back street then they go to a track day like rezz's photos with stillways track weapon RX7.

Signal, Kansai and veilside also feature. Signal take a 2.8L R34 GTR on the high way for a 300Km/h run

Link to comment
https://www.sau.com.au/forums/topic/126842-garage-stillway/#findComment-2381076
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...