Jump to content
SAU Community

Recommended Posts

For Sale.

SR20DET manual ECU $150

SR20det manual gearbox, sold as replacement(no shifter/etc) $550

R32 GTR FRP bar with moulded in lower lip that fits R32 GTS-T.

Has been repaired and is in primer. I have 2 of these $150 each.

R32 GTR ally Bonnet in gun metal grey, damaged with lip folded over. $150

Autometer carbon back boost gauge with micro line. $30.

All items are not sold until cash is in hand. You can PM me all you want saying "you will take it" but first to my door with money is the buyer.

In Perth WA, will COD at buyers expense.

Can you send me pics to i want bumper

Email : [email protected]

This bumper bar will it fit the gtr grill and bonnet to cause you said its folded to fit the gts-t but i want to change the bonnet bumper and grill to gtr style?

Can this be done?

And will you send to melbourne?

Ok found some pics I have.

This is one front bar on GTR guards(fits ok) and the GTR bonnet.

http://butters.gallery.netspace.net.au/alb...Front_Small_004

http://butters.gallery.netspace.net.au/alb...rner3_Small_003

I have two PM"s saying they will take the bars, so they most likely sold. Will keep you posted :blink:

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...