Jump to content
SAU Community

Bridgestone RE540's

EVL R33

By EVL R33,
in Western Australia

 Share

Recommended Posts

rev210 Grand Master

rev210

Posted
Posted

Adam,

It's more the case that people farkup their standard street cars handling with half baked ideas re: tyres and suspension. They are often putting mismatched parts together, assuming that if itsenough for a race car its good enought for their car (and will make it faster).

Very low profile tyres are more a cosmetic gimmic than an actual performance enhancer. At best it does nothing and at worst it just doesn't provide the feel and grip of a little taller profile.

I have driven a couple of skylines with coil overs and wider aftermarket rims and tyres and can only say that most would not keep up with my stockie aound corners.

The atessa system or any 4wd helps no argument, but the concept of sidewal flex (ideally on tyres designed to do this) is just as important irrespective. GTR's will go quicker on slicks and that is the model of sidewall flex you try to copy with street tyres for the drags.

macka Veteran

macka

Posted
Posted
Originally posted by KILLER-T

Hi ya Brett if you are buyin the re540s for the drags then dont bother the side walls are way to hard to get any advantage from them on the 1/4 mile but for a track tyre they would be great.I cant tell you what they are like in the wet but on a dry road the are the best thing i have used.The only thing i dont like about them is the amount of road noise they make

Thats his excuse for poor drag times :P

I thought RE540's were sticky maybe me and you shoul swap i have some rippers ;)

:bahaha:

rev210 Grand Master

rev210

Posted
Posted
Originally posted by XRW

Gts its more that 540's react to the VHT and do the opsite and become more skatey than they do grippy..

I don't know who told you that but, it sounds like bulldust. Or perhaps they meant doesn't become as sticky as other tyres or even 'they are sticky to start with and the vht doesn't add much extra'.

Vht makes rubber compound tyres 'sticky' even tyres with silicone content. We found some tyres better than others in terms of responding to VHT (they all got more sticky tho'). Back in the days when you rigged a squirter bottle over the rear tyres so the officials couldn't see it when you did the burnout on street meet days (they still seem to skim on track treatment these days too).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...