Jump to content
SAU Community

Recommended Posts

Hi guys,

I want to buy a boost guage. I really like the ones that illuminate EL, but i am open to anything that is of good quality and looks awesome. Im finding it hard to find decent stuff locally... maybe i need to buy from overseas?

Im just after a single gauge for boost and will most likely mount on the dash infront of steering wheel, it behind the steering wheel so i see it thru thr hole you know? Dont want trouble off the coppers!

Cheers

Rob

Link to comment
https://www.sau.com.au/forums/topic/129017-wtb-boost-gauge/
Share on other sites

Ok i am very interested in getting the Black face Apexi EL mechanical. Anyone know somewhere decent priced that sells it? Nengun are out of stock.

Also, is there any significant downside to mechanical instead of electronic for the gauge?

Link to comment
https://www.sau.com.au/forums/topic/129017-wtb-boost-gauge/#findComment-2388166
Share on other sites

I have a no-brand hand-me-down boost gauge at the workshop - it came off my car; rattles when on boost; has scratches on the cup and the nipple where the vacc line goes on is busted. Yours for $5.00 (which is 50% off what I paid)

The buyer of this item will be the 4th owner - it's been a good gauge; it's served us all well (kinda)

Link to comment
https://www.sau.com.au/forums/topic/129017-wtb-boost-gauge/#findComment-2388190
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...