Jump to content
SAU Community

Motec M4 Clubman Ecu

DCR
 Share

Recommended Posts

DCR Apprentice

DCR

Posted
Posted

Selling my Motec M4 Clubman. I am going something different and therefore no longer need this. I have never used it and purchased it privately about 6 months ago. I know the person whom I purchased it from and he has told me it works perfectly when running on his RX7 13B Turbo. Has had the latest software (V6.2) loaded from the motec website. Can be up-spec'd to M4 Pro by any Motec technician. Comes complete with PC cable and ECU plug. Contact Motec on 03-9761-5050 and give them the serial number to check the validity of the ecu. Serial number is shown in the pics.

Motec M4 Clubman Specs

$1500 + Postage. I will only send via registered mail. Pick up in Brisbane.

If you need to know more Email Me

Motec%20M4%20Clubman.jpg

Motec%20Complete.jpg

Motec%20Serial.jpg

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/129869-motec-m4-clubman-ecu/
Share on other sites
kjb_r33 Experienced

kjb_r33

Posted
Posted
do they run on S2 R33?

Will run a 33, but you would also need an ignition expander, (relatively cheap, around 400 i think), and you would not be able to run sequential injection as there is only 4 injector drivers.

DCR Apprentice

DCR

Posted
  • Author
Posted
Will run a 33, but you would also need an ignition expander, (relatively cheap, around 400 i think), and you would not be able to run sequential injection as there is only 4 injector drivers.

You may want to check that on the motec specs list.

kjb_r33 Experienced

kjb_r33

Posted
Posted (edited)
You may want to check that on the motec specs list.

From the MOTEC webpage:

Injection

* 4 group sequential

* User programmable injector current 0.5~12 Amps peak

* Battery Comp to suit any injector

Ignition Outputs

* Up to 4 Ignition Outputs

* Versatile Ignition Interface allows connection to most OEM ignition systems including:

o Nissan Multi Coil modules

o GM EST DFI systems

o FORD EDIS DFI systems

o Mazda Rotary DFI modules

o Many Others

Which means you can run UPTO 4 individual injectors for sequential, any more than that you have to run grouped injection and last time i looked the rb has 6 injectors.

Same as the ignition outputs, you could run waste spark ie THREE coil packs, but not SIX coils as the RB's have. You need the motec ignition expander for that, which then only uses ONE ignition output from the M4.

Edited by kjb_r33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...