Jump to content
SAU Community

Tomei Poncams Direct Bolt In For Rb26

varun_gtr
 Share

Recommended Posts

varun_gtr Enthusiast

varun_gtr

Posted
Posted

Tomei Poncams direct bolt in for r32 & r33 rb26 will not fit in r34 rb26 because of different crank angle sensor drive. Very noticable change throughout the whole rev range sounds tuff on idle. The inlet cam has done around 6000km the exhaust cam is brand new and never been run and cost me $680 on its own from high octane racing in sydney.

Part numbers:

Inlet cam - A2691N

Exhaust cam - A2691X

$850 delivered anyway in aus. located in brisbane.

Contact me on 0401376402 or [email protected]

varun_gtr Enthusiast

varun_gtr

Posted
  • Author
Posted

ye im going bigger just for a bit of overkill im not sure if i'll make to the power theshold of these cams but just incase, but these cams with the right bits can produce 450kw+ and low run low 10sec passes and has been proved by a mob down south with a sliver r32 gt-r.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...