Jump to content
SAU Community

Gb: Brand New Z32 Afm's - $330.00 Each


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Blitz, this may seem like a sil question, but is there any difference between the genuine Bosch item and a Nismo one?

The Bosch/Nissan Z32 AFM's are 80mm,where the Nismo/Tomei units are smaller in physical size, but still have increased voltage capabilities over the standard AFM - They are also significantly more expensive and tuners I have spoken to seem to prefer the standard type 80mm Z32 over the Nismo/Tomei type units.

Hope this helps

Payment made and email sent to Darron

Alan

Hi Alan, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581246)

Cheers,

Nick

Received the AFM yesterday, damn quick delivery :ninja: Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Your very welcome mate :ninja:

Payment made and email sent to Darron :ninja:

Gday Matt, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581247)

Cheers,

Nick

CAn you hook these units up to a stock RB20DET and see a difference or will it be just a waste of time until i get my Power FC?

Thanks guys

You will need to wait until you have a Power FC :D

Woohoo! Received mine today! thanks mate! :D

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Received the AFM yesterday, damn quick delivery :D Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Hey AcoustiK, try this thread, might help you a bit! :yes:

http://www.skylinesaustralia.com/forums/in...howtopic=116520

Woohoo! Received mine today! thanks mate! ;)

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Hi Dave, glad to hear it arrived safely - The dent in the mesh wont be a problem, in some cases people remove the mesh all together.

Hey Blitz,

Just transfered the funds, and emailed Darron too.

Thanks

Hi Nikki, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581250)

Cheers,

Nick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...