Jump to content
SAU Community

Gb: Brand New Z32 Afm's - $330.00 Each


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Blitz, this may seem like a sil question, but is there any difference between the genuine Bosch item and a Nismo one?

The Bosch/Nissan Z32 AFM's are 80mm,where the Nismo/Tomei units are smaller in physical size, but still have increased voltage capabilities over the standard AFM - They are also significantly more expensive and tuners I have spoken to seem to prefer the standard type 80mm Z32 over the Nismo/Tomei type units.

Hope this helps

Payment made and email sent to Darron

Alan

Hi Alan, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581246)

Cheers,

Nick

Received the AFM yesterday, damn quick delivery :ninja: Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Your very welcome mate :ninja:

Payment made and email sent to Darron :ninja:

Gday Matt, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581247)

Cheers,

Nick

CAn you hook these units up to a stock RB20DET and see a difference or will it be just a waste of time until i get my Power FC?

Thanks guys

You will need to wait until you have a Power FC :D

Woohoo! Received mine today! thanks mate! :D

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Received the AFM yesterday, damn quick delivery :D Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Hey AcoustiK, try this thread, might help you a bit! :yes:

http://www.skylinesaustralia.com/forums/in...howtopic=116520

Woohoo! Received mine today! thanks mate! ;)

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Hi Dave, glad to hear it arrived safely - The dent in the mesh wont be a problem, in some cases people remove the mesh all together.

Hey Blitz,

Just transfered the funds, and emailed Darron too.

Thanks

Hi Nikki, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581250)

Cheers,

Nick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...