Jump to content
SAU Community

Recommended Posts

hi all,

my battery keep on dieing, i drove the car everyweekend and only on the weekend. but lately i have to push start the car to get it going, would it be the alternater? wild driving it read 14.2v but wheni turn the car off it instantly gone to 12.7v i tried changing the baterry it didnt help. how much can i get a new alternater for including fitting, also would a maxima ultinator be ok? thanks for ur help.

Link to comment
https://www.sau.com.au/forums/topic/130518-battery/
Share on other sites

each battery has an amp hours rating.. so it can supply say 60amp hours

EDIT : was slightly off lol

Amp Hours

The Amp Hour rating tells you how much amperage is available when discharged evenly over a 20 hour period. The amp hour rating is cumulative, so in order to know how many constant amps the battery will output for 20 hours, you have to divide the amp hour rating by 20. Example: If a battery has an amp hour rating of 75, dividing by 20 = 3.75. Such a battery can carry a 3.75 amp load for 20 hours before dropping to 10.5 volts. (10.5 volts is the fully discharged level, at which point the battery needs to be recharged.) A battery with an amp hour rating of 55 will carry a 2.75 amp load for 20 hours before dropping to 10.5 volts.

i have the same issue with my car as its a weekender too.

solar panel charging is how i fixed it up

Edited by Craved
Link to comment
https://www.sau.com.au/forums/topic/130518-battery/#findComment-2415489
Share on other sites

each battery has an amp hours rating.. so it can supply say 60amp hours

EDIT : was slightly off lol

Amp Hours

The Amp Hour rating tells you how much amperage is available when discharged evenly over a 20 hour period. The amp hour rating is cumulative, so in order to know how many constant amps the battery will output for 20 hours, you have to divide the amp hour rating by 20. Example: If a battery has an amp hour rating of 75, dividing by 20 = 3.75. Such a battery can carry a 3.75 amp load for 20 hours before dropping to 10.5 volts. (10.5 volts is the fully discharged level, at which point the battery needs to be recharged.) A battery with an amp hour rating of 55 will carry a 2.75 amp load for 20 hours before dropping to 10.5 volts.

i have the same issue with my car as its a weekender too.

solar panel charging is how i fixed it up

so you dont think its the alternator? how will i know if the afternator is no longer working correctly?

Link to comment
https://www.sau.com.au/forums/topic/130518-battery/#findComment-2415568
Share on other sites

the charge the battery recieves should always be around 14.5v from the alternator.. if its above or well below that it would need to be looked at . ie make sure its belt is not slipping etc

try what Blind_elk said .. the charge value should remain the same from idle to all revs.. shouldn't change dramatically

Link to comment
https://www.sau.com.au/forums/topic/130518-battery/#findComment-2415635
Share on other sites

the charge the battery recieves should always be around 14.5v from the alternator.. if its above or well below that it would need to be looked at . ie make sure its belt is not slipping etc

try what Blind_elk said .. the charge value should remain the same from idle to all revs.. shouldn't change dramatically

i forgot to mention that i drove the car on sunday for a good hour and today i need to push start. this is the second bettery, both were 1 year old.

Edited by bluer33
Link to comment
https://www.sau.com.au/forums/topic/130518-battery/#findComment-2415658
Share on other sites

i've had this happen in a few of my daily drivers. can drive around at night, then next morning they are dead. only happens in winter. its the cold weather that kills batteries. you may've bought the battery 12 months ago, but it may've been sitting on the shelf for 6 months before that. get a new battery and it should be all good. get a century, since they have a warranty.

Edited by mad082
Link to comment
https://www.sau.com.au/forums/topic/130518-battery/#findComment-2416497
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...