Jump to content
SAU Community

Recommended Posts

ok heres the problem, rb25pfc on a rb20 using rb20 base maps...

greddy/denso 720cc injectors with dropping resistors to suit.

doing the injector correction math for the power fc 370 / 720 = .515 or so so 51.5% correction on the power fc.

inputting the said 51% change into the power fc causes the car to run EXTREMELY lean and can only be compensated at that setting by changing the lagtimes for the injectors to +70 or so.

not sure what the deal is here or why its running so lean, anyone have any ideas?

Link to comment
https://www.sau.com.au/forums/topic/131130-power-fc-oddities/
Share on other sites

why are u using resistors (sorry if its something obvious) but i dont see why?

are they the wrong impedance or type? there should be no reason it will run mega rich or lean with different injectors, providing the right values are dialed in

ok heres the problem, rb25pfc on a rb20 using rb20 base maps...

greddy/denso 720cc injectors with dropping resistors to suit.

doing the injector correction math for the power fc 370 / 720 = .515 or so so 51.5% correction on the power fc.

inputting the said 51% change into the power fc causes the car to run EXTREMELY lean and can only be compensated at that setting by changing the lagtimes for the injectors to +70 or so.

not sure what the deal is here or why its running so lean, anyone have any ideas?

For that ratio to work both injectors must be statically flowed at the same pressure. Which is how most injectors can be compared. However the flow rate of 1 injector at x ms could be alot different to another injector at the same millisecond -this is where comparing injectors at a signgle duty cycle is useless. What I am trying to say is that the ratio used by PFC is not exact.

ok heres the problem, rb25pfc on a rb20 using rb20 base maps...

greddy/denso 720cc injectors with dropping resistors to suit.

doing the injector correction math for the power fc 370 / 720 = .515 or so so 51.5% correction on the power fc.

inputting the said 51% change into the power fc causes the car to run EXTREMELY lean and can only be compensated at that setting by changing the lagtimes for the injectors to +70 or so.

not sure what the deal is here or why its running so lean, anyone have any ideas?

I would have input 48.5% to reduce 720 cc down to 370 cc's equivalent.

:) cheers ;)

Edited by Sydneykid

paul - resistor pack is on there from when i was running the std rb20 ecu, as it used for running low impedence injectors on a high impedence system...

greddy injectors are 3ohms give or take, so that would neccsistate running the resistor pack to keep the car (ecu) from farking its self up no?

Edited by carl h
ok heres the problem, rb25pfc on a rb20 using rb20 base maps...

greddy/denso 720cc injectors with dropping resistors to suit.

doing the injector correction math for the power fc 370 / 720 = .515 or so so 51.5% correction on the power fc.

inputting the said 51% change into the power fc causes the car to run EXTREMELY lean and can only be compensated at that setting by changing the lagtimes for the injectors to +70 or so.

not sure what the deal is here or why its running so lean, anyone have any ideas?

That function is there only to offer a basic starting point for your next tune. Back to the dyno my friend.

with swapping 2 wires round and clipping one it plugs right in and runs fine, will even run on the rb25 base maps but runs poorly due to the lack of ignition in the map.

ive realized that the compensation bit isnt as apex described and gonna go back to what i was doing before with changing correction till i get the afr at idle thats ideal (14.5) and going from there...seems to work better that way.

with swapping 2 wires round and clipping one it plugs right in and runs fine, will even run on the rb25 base maps but runs poorly due to the lack of ignition in the map.

Wow! Do you have a link to any information on how to do this? As i don't really see the value in paying $1500 for a AP Engineering Unit when you can buy an RB25 one for $900ish, when its pretty much the same!?

pardon my ignorance…

but of you are running rb20 base maps, then shouldn’t your formula be using the rb20 standard injectors?

As in 270cc…

I was under the impression rb20 was 270cc and rb25 was 370cc

no even tho im running the base maps for the rb20 it still is a rb25 power fc and there for expects 370cc injectors as stock...

and as far as base maps are concerned, yes they are basemaps but they are also VERY good starting points no one said they would be perfect.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...