Jump to content
SAU Community

Recommended Posts

All parts are in fine working order as they were pulled off my own car only due to upgrading or bought and no longer required.

Im in Brisbane Southside, but will send anywhere at buyers expense.

Email me HERE if any queries, questions, or more pics.

Thanks. :sorcerer:

R32 GTR Gearbox with transfer case- $1000

Traveled aprox 72,000kms, synros are perfect, was only run behind a stock motor.

Gearbox Pic 1

Gearbox Pic 2

Transfer Case Pic

Impul Hi-Power Ecu: $250

- Better air fuel ratios

- Takes out speed cut

- Increases rev limit to 9000rpm

- Tweaked fuel maps so you can run more boost safely

- Plugs straight in, no other modifications required

Impul High Power ECU Unit Pic

R32 GTR brake lines for all four corners-$50

32gtrbrakelines.jpg

R32 GTR Intercooler piping -$100

32gtrcoolerpiping.jpg

R32 GTR Thermo Fan -$100

- Perfectly Working Thermo fan only removed to gain extra space in the front

32gtrfan.jpg

32gtrfan2.jpg

R32 GTR Fog Lights -$100

- Fine working factory Fog lights!

R32gtrfoglamps.jpg

R32 GTR Springs and Inserts -$300

- Need to pass compliance inspection or clear a defect?

R32gtrsusp.jpg

R32gtrsusp1.jpg

R32gtrsusp2.jpg

RB26DETT Brand New OEM Nissan Water Pump -$150

- Brand New still in the box!

R33 GTR RB26DETT stock cam gears-$50

- only removed due to upgrading to adjustable.

R33 GTR Cam Gears.jpg

Edited by CameronBNR32
  • 5 months later...
Still keen to check some close up pics off the rims!

Sorry, have been abit busy. I Took some pics of the rims today..

Edited by CameronBNR32
Sorry, have been abit busy. I Took some pics of the rims today..

Click here for GTR Rim close ups

Will take the rims for $500 if you are cool with that?

Got a quote to get them shipped, so can pick up right away!

Just need an adress? Give me a call on 0412913213 or post your

number if you want me to call to arrange payment?

Thanks Joey...

Will take the rims for $500 if you are cool with that?

Got a quote to get them shipped, so can pick up right away!

Just need an adress? Give me a call on 0412913213 or post your

number if you want me to call to arrange payment?

Thanks Joey...

Hey,

$500 is too cheap for me sorry, for the condition they are in I believe $600 is cheap, I've seen sets that are in worse condition go for ~$700

Hey,

$500 is too cheap for me sorry, for the condition they are in I believe $600 is cheap, I've seen sets that are in worse condition go for ~$700

No worries mate, shipping to were i am will cost me $150-$180

But...

Whats the approx wieght each? So i can get an exact price on shipping?

Thanks again

Joey.

No worries mate, shipping to were i am will cost me $150-$180

But...

Whats the approx wieght each? So i can get an exact price on shipping?

Thanks again

Joey.

Hey the rims weigh 7.5kg each

thanks

  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...