Jump to content
SAU Community

Help Wildcat Out

Wildcat

By Wildcat,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Wildcat Grand Master

Wildcat

Posted
Posted

hi all

Its a lovely day here in Perth (not,,,bloody horrible actually :wub:)...I went to turn my back window wiper on only to find that it did nothing :( I turned it onto the On position and all i could see was the top bit moving and the wiper and holder move downwards and thats where it stayed :D

Is this a sign that it has died :bunny: or that i have a wire lose or does something need tightening :D my first impressions where that if i could see it move that it was probably not dead...but with weather like this it is almost impossible to see anything out of my back window..and ideas would be greatly appreciated :bunny:

Thanks champs

Wildcat :D

Link to comment
https://www.sau.com.au/forums/topic/132377-help-wildcat-out/
Share on other sites
Ska Grand Master

Ska

Posted
Posted

First thing would be check fuses

Other then that you'll have to do what i had to do for a full diagnostic, meaning take the cowling off the top and bottom of the steering column, there are 9 screws underneath, and check the 4 wire plug on the left of the steering column.

Then get an electrical type person to "close the circuts" and "check for eath" and "check for positive" with and without the switch being on.

then check the wiring running from the steering column, under the dash, under the drivers side foot/kick panel, under the drivers seat, under the drivers side passenger seat, behind the plastic under the back drivers side glass and then through to the back door.

then manually close the circut on the wiper motor to see if it works independantly from the switched wiring, get positive from somewhere else.

from that I determined that the wiring going to the switch from the old ecu was somehow lost in the spaghetti going into the power-fc, which is somehwere in the dash.

So I'm just going to manually rewire the switch, easiest solution for me :(

Wildcat Grand Master

Wildcat

Posted
  • Author
Posted
First thing would be check fuses

Other then that you'll have to do what i had to do for a full diagnostic, meaning take the cowling off the top and bottom of the steering column, there are 9 screws underneath, and check the 4 wire plug on the left of the steering column.

Then get an electrical type person to "close the circuts" and "check for eath" and "check for positive" with and without the switch being on.

then check the wiring running from the steering column, under the dash, under the drivers side foot/kick panel, under the drivers seat, under the drivers side passenger seat, behind the plastic under the back drivers side glass and then through to the back door.

then manually close the circut on the wiper motor to see if it works independantly from the switched wiring, get positive from somewhere else.

from that I determined that the wiring going to the switch from the old ecu was somehow lost in the spaghetti going into the power-fc, which is somehwere in the dash.

So I'm just going to manually rewire the switch, easiest solution for me :no:

:) oh my :rofl: that sounds like a long job...might check if its a fuse if not i will learn to have something broken :huh: thanks for your help champ

Revhead Grand Master

Revhead

Posted
Posted

From your description it sounds like somehow the wiper arm has detached itself from the motor. I don't remember how Stag tailgates are put together but if you can get at it, check to see if a clip hasn't just fallen off or something. If you're not mechanically minded it might be worth taking it to a workshop and mention that you think this might be the case and ask them to look at it. Get someone to recommend a shop that won't take you for a ride (SAUWA club sponsors would be a good place to start) and possibly take a guy with you, from your sig I'm guessing you're female. Yes it's sexist, but some shops do still overcharge or outright lie to women if they think they can get away with it.

If you want to check it, turn the rear wiper on, then go to the back of the car. If you can hear the wiper motor going, it's not wiring, fuses or a relay so you can avoid the nasty job of getting into the dash and steering column :rofl:

ish Proficient

ish

Posted
Posted

I agree with Revhead.

It happened to me while I was borrowing my mum's r31 so i had to fix it for her.

Its is a bit tricky to get at and you have to concertrate on the links being the right way round or the wipers will try to stop up the top in stead of tucked away. :rofl:

Wildcat Grand Master

Wildcat

Posted
  • Author
Posted (edited)
If you want to check it, turn the rear wiper on, then go to the back of the car. If you can hear the wiper motor going, it's not wiring, fuses or a relay so you can avoid the nasty job of getting into the dash and steering column :)

ok i went to the back of the car if i lift the wiper up it is really loose and moves around if i let go of it, it falls to the ground. Then i put it back on the down on the window turned it on and you can see the round bit just before the wiper blade/holder itself trying to lift it up but nothing happens... :rofl:

Edit* forgot to mention that i can see the round bit actually rotating around and hear the motor going but the blade just wont move...driving me nuts jks

Edited by Wildcat
Wildcat Grand Master

Wildcat

Posted
  • Author
Posted
Sounds like it should be a relatively easy fix then :no:

Like a steering wheel down the pants?

:rofl: bit uncomfortable me thinks but i could probably handle that :huh: as long as it wasnt my steering wheel :) just jokes

back on topic im hoping that it will be easy enough to fix :O

Wildcat Grand Master

Wildcat

Posted
  • Author
Posted
Obviously not !! :O

:P should be an easy fix then........... for hubby (with supervision by the sounds of it)!

oh mister tangles :) i have faith..i just like to be independent and being a girl and all i would like to be able to do things that men think only they can do :P but of course hubby can look at it and fix it and i can watch :laugh::laugh:

MrGTST Grand Master

MrGTST

Posted
Posted
oh mister tangles :blink: i have faith..i just like to be independent and being a girl and all i would like to be able to do things that men think only they can do :P but of course hubby can look at it and fix it and i can watch :P:)

You just make sure my dinner is ready for when I get home ... thats a good girl :wave:

Could you also please make sure the spare bed is made so I have somewhere to sleep tonight :P:laugh::laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • Matt Z
      SAU NSW - Bathurst Run 2025

      By Matt Z · Posted

      🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
×
×
  • Create New...