Jump to content
SAU Community

Recommended Posts

Ok so I bought my car knowing the engine was run without oil to the point of the exhaust cam seizing. This was the result after an aftermarket oil hose fitting un-screwed itself.

After some good advice from some members on here I have decided to ditch the old engine for a possible rebuild down the track... Will also come in handy for spares.

My question is this- For the amount of time the engine was run with no oil (presumably with some boosting?)

Is there any chance there would be some minor damage made to the turbo bearing?

Turbo in question is an HKS T04e

Also could anyone help with the hp rating of my turbo? Only numbers I can see is .50 wich is the A/R of the front cover yes?

Every other T04e I have seen for RB20/25 has either the .56 or .60 front cover.. Is my turbo designed for slightly quicker spooling compared these, While sacrificing on overall power?

Edited by Drift_Limo
Link to comment
https://www.sau.com.au/forums/topic/132658-turbo-oil-feed-starvation/
Share on other sites

You have asked 2 questions;

1. Is the turbo damaged? No idea, no way to tell, waste of time guessing. Take it to turbo workshop and have it checked.

2. HKS don’t publish compressor maps. Last time I bothered looking, there were 6 or 7 specifications of Garrett “T04E”. Outputs ranging from 350 bhp to around 500 bhp, so take your pick.

:ermm: cheers :(

I would guess that if the turbo was being boosted without oil long enough for the engine to run out of oil and seize the camshaft, the turbo will be shagged, and thet may be the least of your problems, for the $150 or so, i would rip the sump off and have a quick look at the bearings

Suggest you locate the CHRA ID tag number, and post up that, along with any numbers off the housings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...