Jump to content
SAU Community

Well I've Never Seen All 4 Off The Ground...

JaFF

By JaFF,
in Motorsport Discussion & Builds

 Share

Recommended Posts

2rismo Grand Master

2rismo

Posted
Posted
We have just come online to have a quick sneak & thought it would be good to let everybody know what caused this massive wheel stand. We have just rebuilt the 600 ci motor & made a new sheet metal manifold which produced an extra 100 HP & 30 ft lbs for a new total of 1260 HP & 875 ft lbs.We also designed the manifold different to all previous manifolds which resulted in an unbelievable acceleration rate on the dyno, like nothing we had ever seen before.

Whilst testing the motor we also used VP SVO5 & this fuel has a lower spec gravity to C14+ which caused the floats to actually run slightly low. It took 3 runs for us to figure out why the car had not shown any more power or even quicker 60 ft times. This was due to the front jets being uncovered when wheel standing. After we raised the floats back up the engine did not stay at 6200 rpm off the start line for 2 seconds like previous, instead it went straight from 6200 to 6700 & continued to climb rapidly to 7500 whilst still moving upwards. This extra acceleration cause the wheelie bars to bend further up & bottom out on the rear of the car which actually cause them to bend & not hold the car down at all, like it has done for 3 years now.

When i left the line i knew that something was wrong in the wheelie bar department due to only seeing blue sky for way too long, but I knew if I got out of the throttle the car would come down & totally smash everything underneath, so I kept my foot on the throttle until it came back down totally. After the car settled I removed my foot only to realise that the throttle was actually stuck on full. I looked at the tacho & it was somewhere around 8600 & new the rev limited was set to 8700, so as soon as the limiter took hold of the motor I selected neutral & hit the kill switch to end this wild but exciting ride.

I will be online for another 10 minutes, please feel free to reply if you would like to ask any questions.

Trick & Mansweto Racing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...