Jump to content
SAU Community

Recommended Posts

I just finished running the new motor in on the dyno and did a base tune

The vehicle has undergone alot of Development now

Engine

Nitrated R33 GTR crank

H beam Eagle Rods

Venoila 9.2 Comp Pistons

Tommie Head Gasket

Solid Lifter Conversion

Big cams

GT 1100 hp bb turbo

2 speed powerglide

2 stage single sprayer nos kits

It has made 485 rwhp on 10 psi @8500rpm

I will post the Dyno sheet on 2morrow with the run on 30 psi

hopefully make around 800 rwhp

I should be at the track in the next 2 weeks

I will also post picts with photos of the new engine bay and if someone can host a video clip ill appreciate it

Edited by MR331307
Link to comment
https://www.sau.com.au/forums/topic/135859-lnemup/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hello everyone

I just did a safe tune on the vehicle and it made a total of 648 rwhp @ 30 psi on a 10.2 AFR

I am going to do some more Tuning on it to get it to 720 or so RWHP But im waiting on a MSD dis 4 before i can run more boost and before i start bumping up the timing.ill hit the track next wenesday night.Aiming in the 9`s somewhere

Hopefully towards the end of the year i can run in the high 8 area,

I havent installed the CHUTE yet but i will after i get back on wenesday.

ILL post up some Dyno Picts and Videos soon3

Its still the RB25 Block just with GTR crank,Eagle Rods,Venoila 9.2 comp Pistons.

The car makes power to 9000rpm which will be fun at the track

When everyone sees us up there come up and say hello

Edited by MR331307
Link to comment
https://www.sau.com.au/forums/topic/135859-lnemup/#findComment-2542799
Share on other sites

around 6300 without nitrous

but i got nitrous on till 18 psi so i can gety on boost quickly and it gets on boost around 5700

Ive had lnemup plates for around 4 years

and the venoila pistons are pretty good quailty so i shouldnt have a problem

Edited by MR331307
Link to comment
https://www.sau.com.au/forums/topic/135859-lnemup/#findComment-2544094
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...