Jump to content
SAU Community

R33 Front Light Globes

donut_kng

By donut_kng,
in General Maintenance

 Share

Recommended Posts

donut_kng Experienced

donut_kng

Posted
Posted

Hi, I'm looking aorund to buy new globes for the front of my series 2 r33, have asked around a few shops, although nobody seems to know the exact globe type suits the:

headlights

parker lights

high beams and

round fog lamps.

I am looking to make change everything to phillips crystal vision globes (ice white). Although I need to know what tye of globe fitting/size/type I am asking for!?

If anyone can tell me this would be greatly appreciated!

Link to comment
https://www.sau.com.au/forums/topic/135982-r33-front-light-globes/
Share on other sites
Kinks Grand Master

Kinks

Posted
Posted

don't use any globe with a blue tint on the lens.

it inevitably cuts your light output and blue light is worse for visibility because it scatters easily when it hits air/water. this creates glare.

plus-50's FTW.

mad082 Grand Master

mad082

Posted
Posted
I want something that will give off the most light, not because it looks blue

phillips plus 50's

Yes I am after something thats bright white, not blue as they look cheap as. Any Ideas?

phillips blue vision give off a white-ish light, but it is only as bright as a standard bulb. i currently use them and they are better in the skyline than in other cars i've owned. i also have phillips gt150's in my other car and they work well. give off a white-ish light, but are yellower than the blue vision, and from the front have a blue reflection in them.

i'm not 100% sure, but i don't think BATMBL's bulbs are legal either. i don't think they have been ADR approved for road use, which means if you have a crash at night where you hit someone or something, your insurance company can say that your lights were part of the cause and refuse to pay up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...