Jump to content
SAU Community

Twin Turbo Kit For Rb25/30

kaotik
 Share

Recommended Posts

kaotik Enthusiast

kaotik

Posted
Posted (edited)

for sale is the turbo kit from my skyline in the 'whole cars' section as i am considering selling it as parts

it will fit an rb25/30 with an rb25 head

its a sub zero setup as featured on one of they're customers cars in a previous issue of zoom magazine

the car did a 10.9 1/4 mile with 326rwkw

consisting of..

custom stainless manifold

subzero 40mm wastegate

2x t3/4 turbos (rear housing from vl turbo)

pipes to intercooler

air filters and pipes

braided oil and water lines

all hoses and clamps

stainless dump pipes and Y joint to cat

all u have to do is bolt it on

can see running on car

on my car it produced 356rkw @ 19psi when i ran out of spark

could easily produce over 400rwkw

post-3401-1159183121.jpgpost-3401-1159184121.jpgpost-3401-1159184646.jpg

asking $2000ono. located in western sydney

[email protected] for more info

Edited by kaotik
Link to comment
https://www.sau.com.au/forums/topic/136027-twin-turbo-kit-for-rb2530/
Share on other sites
kaotik Enthusiast

kaotik

Posted
  • Author
Posted
selling any internals? What other parts are needed to get these running?

selling injectors x6 blitz 1000cc top feeds $950 and ill throw in a gtr fuel rail

not selling internals

the whole kit is complete to bolt on, u just need to meet up the cooler piping and exhaust piping and remove ur air cond

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Good tips, will get on those tomorrow. When doing the maintenance I did move a few of those connectors around, and things that are old tend to not like moving around. (Like me).
    • GTSBoy
      Yet another RB Neo misfiring thread after reading all the others.

      By GTSBoy · Posted

      Don't try it. It will be shit. Better chance of damaging the engine than gaining any knowledge about the old one. Maybe, but unlikely, especially if the O2 sensor is working. You can use NissDataScan to look at the stock ECU.   Cleaning the AFM is seldom necessary and seldom helps. The R35 coil & loom conversion should eliminate dud coils or plugs. But as you still have misses - look to the plug where the coil loom connects to the engine loom, and the CAS plug. Need quality connections there. Also look to injector plugs. And the AFM plug while you're at it. Also look to whether your injectors are clean and flowing evenly. Get them out and onto a testbench.
    • uchoa
      Howdy from the states.

      By uchoa · Posted

      Good to know, I feel like I am in for a rollercoaster ride that looks like a sine wave. 
    • GTSBoy
      Howdy from the states.

      By GTSBoy · Posted

      You'll fit right in. Acceptance is the first step.
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Hey folks. I've been lurking and browsing the forum for a while, since I got into my head that I wanted a skyline. Having purchased an overpriced completely stock GTT, (only "mods" it has is HKS pod filter and catback) now that it became legal in the US, it was all glorious and sututu noises here and there. But then I wanted to do things right and went to do basic maintenance. After all the fluids, filters done, I did the spark plugs, that's when the problems started.. First the car started spluttering at around 4.5k RPM. Which I gapped down the new plugs and that solved the sputter there, but the car now always misfires at idle with pops when lifting off and shifting 2nd to 3rd. Similar to the issues in this recent thread. I've been banging my head against the wall, reading the threads here and trying suggestions for a couple months now, so decided to start this one to explain exactly what I tried and what is going on. The symptoms of the issue: Idle and low revs misfiring intermittently. You can hear the exhaust tone change and the shakes on the shifter knob. It happens frequently, but doesn't seem to have a rhythm to it. Pops when backing off throttle. It pops and or burbles almost feels like it spits fire when it pops. (Happens mostly in 3rd gear at around 2k RPM). When under load and after 6k RPM, it also pops when shifting from 2nd to 3rd. There's a ticking noise at around 2k RPM in 2nd gear going downhill, seems unrelated though but I am out of educated and downright dumb guesses. Not noticeable lack of power when putting the car into load. The attempted diagnosis and solutions: Unplugging coils when the car is running This did nothing to change the idling and tone shift for every cylinder. Checking the exhaust headers with thermometer They all are within what I'd say it is margin of error of the laser thermometer New spark plugs Tossed two new sets, copper, iridium and using the old ones, still misfiring, even re gapped to 0.8mm, still same thing. MAF cleaned with the "specific" spray cleaner No changes in the issues what so ever. Brand new loom and r35 coil conversion (was going to add the r35 coils anyway) car runs arguably better, still misfires, but seems like does less frequently. Placebo? Code 21 now being thrown, thanks nissan gods. Removed the CAS to check the shaft for play or anything. CAS seems all fine, nothing that indicates any issue, visually speaking. Things to attempted next: Ordered a new MAF (chinesium from Amazon, to be able to return regardless of result). Fuel with proper gas, maybe it is this California water that they sell as gas that is to blame? Plugin the link ECU and check the info using the built in base map. Go back to BMW and eat my rob bearing breakfast without milky oil mixture.   Do any of you have experienced anything like this or have any suggestion?
×
×
  • Create New...