Jump to content
SAU Community

Recommended Posts

not the normal "pull the fuse" type question but here goes

I want to do some burnouts, I know it is best to remove the driveshaft but torque is still transfered to the front wheels, just not put down onto the ground due to well... lacking a drive shaft :)

Soooooo

- if i remove the drive shaft do i still get "full" power to the rears for roasting or only 50% as the other 50 is being transfered through the imaginary drive shaft

or

- if by removing the fuse AND drive shaft, i eliminate the normal "residual pressure" issue will i get more power to the rear?

Hope you all understand what i am asking here...

Link to comment
https://www.sau.com.au/forums/topic/136169-burnouts-in-stagea-question/
Share on other sites

I have pondered this myself Alex,

Depending on how the transfer-case actually works and how the power is "split"... I guess in theory if the front shaft is removed and the 4WD system is still active the clutch packs will be compressed but as they have nothing rotating them they will just sit there happily. The output will be spinning away on the transfer-case (where the front shaft was connected) as will the rear shaft (driving the rear wheels) How much power does it take to spin the disconnected transfer-case? I guess that would be "the loss", and as it is just free-wheeling I can't see how it would drag too much power from the rear drive...

Interested to hear what the actual answer is, but I won't be dropping any wheelies!

I think Japsphere has a good example of how it didn't effect his car on the dyno with a great rear-wheel figure from a stock car.

Cheers

Luke

turning the big chain and gear in the transfer case that drives the front shaft wont take much power at all, though its one damn heavy duty setup when u look inside the transfer case. i drove around in 2wd with no front shaft for the whole 1200km without a hitch and damn did it do some crazy donuts and skids :)

oh the memories :)

wont be long until i do it again with alot more power and ill be sure to get a video of it when i do ;)

i got pics of the transfer case internals on my other hard drive, ill post them up when i get time to show ya's whats inside the case

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey guys I have a 2001 Nissan stagea vq25det, I don't have any engine lights and not really any issues running but I was curious to see if I could use my obd II scanner to find anything that was hidden and I plugged my scanner in and it just said "Low voltage cannot scan" does anyone know how to fix this or what this could be?
    • Sadly we have something in common, our Skyline's like blowing up electrically 😢
    • So, no videos, but, the FAB9 Elite manifold and 68mm Bosch throttle bodies are in stock, but, not the rear part of the air box The FAB9 rear airbox thingie is made with a 3" intake pipe, to suit the 3" intake pipe size of a 68mm throttle body  When they get some more in stock is currently unknown as I'm waiting for FAB9 to reply with a ETA on resupply, my assumption is they outsource their plastic printing stuff to "china", and with the current "tariff war" going on in 'Merica it could be on hold for an undisclosed time Should I pull the pin on the Intake and throttle body, and wait for the airbox?????, that's what I'm thinking... 1. Would the standard 2.75" OEM intake on the air box really be that much of a restriction compared to the 3" naturally aspirated?????? 2. If I don't get the 3" FAB9 airbox fitted at the same time as the intake and throttle body will it need a retune, when/if it eventually turns up?????? As I'm impulsive, to a fault, decisions will be made within....."what's the time now"???....let's say 12 hours......LOL
    • yeah its just so expensive nowadays and its easy to lose motivation very quickly when you start adding up the costs. I acquired the car from a collector in Melbourne and was lucky to get the opportunity to buy something already completed.  I looked at a proper resto and your paying over 300-400K for a proper one (nut and bolt) so this one to me seemed like a much better option! Car is in private storage and for serious buyers, welcome to come see it/drive it in person (photos don't do it justice). 
×
×
  • Create New...