Jump to content
SAU Community

Recommended Posts

Recently upgraded the brakes on my GT-T. Just thought I should mention especially the pads I'm using, which thus far perform well and came in significantly cheaper than some other options I was looking at (i.e. Endless).

They're made by QFM (Queensland Friction Materials), a company I'd never heard of but apparently those in the know reckon they're pretty damn good. I'm using the A.1.RM compound, which is not their most aggressive compound but perfect for street/trackday use. Temp range is apparently 0-700 and coefficient of friction is comparable to the Endless pads with a similar range (CCX, etc.).

The best part is they came in at less than $300 for a set, front and rear. Thus far they perform well, very good from cold with a better pedal feel than the previous Endless pads I've tried (EuroX and NA-R). Not noisy at all either. Can't really comment on dust 'cos my wheels are filthy at the moment... Looking forward to giving them a nice workout at QR in November (thanks MountainRunner).

Otherwise I've gone down the route many here probably have, which is DBA 4000 slotted rotors on the front (RDA don't make 310mm front rotors for the R34 GT-T), RDA slotteds on the rear, braided lines and Motul RBF 600 fluid. Feels pretty damn good so far.

Anyone else here have any experience with the QFM pads?

========

Here's the company blurb:

Queensland Friction Materials P/L is an Australian owned and operated company, specialising in the manufacture of disc brake pads. Key product features include; exceptional performance and pedal feel, low dust, long life with virtually NO disc rotor wear, and excellent cold stopping performance. Non asbestos formulations for automotive and industrial applications, which surpass performance requirements of Australian design rule 31. QFM Disc brake pads are used and recommended by leading Australian brake specialists.

Address: 5/34 Lawrence Drive NERANG QLD 4211

Phone: 07 5596 1099

Facsimile: 07 5596 3347

Email: [email protected]

Link to comment
https://www.sau.com.au/forums/topic/136212-r34-gt-t-brake-upgrade/
Share on other sites

Just cleaned the car today (it was pouring rain so I just squirted some detergent on and went crazy with the sponge!) so I'll keep you guys posted on the dust.

These things pull up so well.... won't be able to comment on how they feel after 5 hot laps until November though. :laugh:

Even if I only get 12 months out of them, at ~$250 for the set WHO CARES????

Initial bite VERY good. I have to re-adjust my reflex in traffic, sometimes getting more stoppage than I intended, though that could also be having the fluid bled properly. Pedal feel is excellent for street.

My previous pads were Bendix Heavy Dutys and the QFM's initial bite is better than these and WAY better than my old Endless EuroX pads. The Endless were awesome once they had some heat into them though, but the QFMs are comparable definitely - tried a couple of big stops on a quiet road last night.

I won't give a final word til I've put them through their paces at QR though.

I'll post pics of dust after a few days driving.

Update for everyone.

Been driving on these for a week now.

Dust is minimal. Better than my old Bendix Heavy Dutys, similar to old Endless EuroX. Pic attached is after 500km of city driving. The wheels were not sparkling clean to begin with - as you can see the dust is minimal.

post-17890-1159884371.jpg

Noise - mild "grinding" noise when cold at very low speeds and pedal pressures. Otherwise no taxi-like squeal. Sometimes a bit of "groaning" as you're coming to a stop down thru 60kmh but this may be due to the rotors.

Pedal feel is very good. Certainly the best I've experienced in my current car. Much easier to modulate the brakes and pedal effort is less, though it would be hard to say how much of this is due to the pads and how much is due to getting the fluid bled. My feeling is that I probably had a little air in the system before.

Performance is good from cold, MUCH better than my previous Endless which definitely had a need to get some heat into them (one hard stop was enough) to work well. I haven't given these a massive thrashing on the road because I don't drive like that on the road as a rule, but with heat they only improve. Certainly haven't got them to fade, which was very easy for me to do with the Bendix HDs.

I'm impressed so far, but I won't be that impressed if the pedal goes long after a lap at QR...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...