Jump to content
SAU Community

Recommended Posts

Hey guys im selling my 94 model sedan,reluctantly. .Ive owned it for 2.5 years and the previous owner had it for 3years.I have done only 10,000ks in that time and also the previous owner only did 8000k per year in it in there ownership.

Engine RB25DET done only 85,000 k with timing belt changed 1500k ago

Oil changed every 4000k and filter

HI flow turbo by ats with to4e wheels in it

HKS stainless dump pipe into 3' pipework,hi flow cat and trust muffler

Split fire coils

Oil cooler and remote oil filter relocation kit

Power fc computer

turbosmart manual gated boost controller ( did have electronic but couldnt get it running right on the dyno)

Micks metal craft cooler 600x300x76and aliminium piping

GFB BOV modified to plumb back

Apexi power intake filter

excedy heavy duty single plate clutch

040 intank bosch pump

Oil catch can

Interior

GTR front seats

Nismo 300kph dash !!! ( Hard to get)

Turbo timer

Genuine floor mat set

apexi EL boost gauge

All the usual mod cons air ,steer,windows etc

M80 mongoose 3 point alarm with immobilisor

Exterior and suspension etc

Genuine Borbet 17'' wheels with 235 45 17 tyres

tein coil overs

Calsonic strut brace

Body is in very good condition

DBA kangaroo paw disc brakes slotted on the front with metal king pads and standard rear.

there will be spares thrown in .

The car has been raced only a few times at willowbank but hasnt been since the turbo etc was done.It ran 13.7 @109mph on the origanal turbo(have time sheet

The car hasnt been thrashed to a point to where something major would go wrong even though it has been race at willowbank.

car comes with rego and roadworthy with the spares thrown in as i wont need when the car goes.There is probably things that i i have forgotten to list.

post-25260-1159688428.jpg

post-25260-1159688692.jpg

post-25260-1159688858.jpg

post-25260-1159689515.jpg

Edited by R334door
Link to comment
https://www.sau.com.au/forums/topic/136422-for-sale-r33-turbo-sedan-with-pics/
Share on other sites

go the 4 doors haaha i've got one, if u wanna sell the apexi pfc seperatly to lower the price let me know, or if a potential buyer 4 the car doesn't have enough $ ...i'd like it 4 the right price (if so does it have hand controller?)

go the 4 doors haaha i've got one, if u wanna sell the apexi pfc seperatly to lower the price let me know, or if a potential buyer 4 the car doesn't have enough $ ...i'd like it 4 the right price (if so does it have hand controller?)

Yeah i does have the hand controller but sorry not selling it off the car.I got it when the power fc's first started to catch on so i paid a dececnt price for it 2 years ago.

  • 2 weeks later...

I can vouch for this car, its a reliable weapon. The only things ive seen go wrong with this is pipes popping off and thats only because he forgot to tighen them, been in it many a time and every time we take it out its like the best rollercoaster its quick handles awesome and its a solid ride not to mention. chris never abuses this car, in fact it would be hard to say which he loves more the 4door or his miss's (its not out of the ordinary for him to spend 1 to 2 days detailing his car on a weekly basis, then go on and continue to improve nitpick the entire car).

Free Bump Chris and good luck on the sale mate

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 3 weeks later...


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...