Jump to content
SAU Community

Recommended Posts

doing a manual conversion in the mr30's would i need to change the tail shaft?? and the other question is what clutches are compatible? as i got a qoute from grand auto and they said a grand for everything except i'll prob need to get my own clutch just doing some research to find out whats the best for it $$

cheers paul

Link to comment
https://www.sau.com.au/forums/topic/136666-2-part-question/
Share on other sites

Paul,

The best of XXEDDY clutches will cost you about $600/700.00 and they make them to handle 3 & 400 rwhp for 280ZXT's, but they are 240mm and to use that size you will need a 260Z 2 + 2 or 280ZX flywheel.

Everything else will be the same as R30.

But if your looking a fairly big HP at the wheels and your going to use one of the top range clutches, you might want to consider a VL Dunnydore slave cylinder, as they are 22mm (7/8) as opposed to the R30's 19mm (3/4)

More fluid, less pedal pressure on big pressure diaphrams?

Cheers, D

Link to comment
https://www.sau.com.au/forums/topic/136666-2-part-question/#findComment-2543114
Share on other sites

Sorry!

Tailshaft I'm not sure about, but if you have a dimension on the Auto one I'll measure the manual spare I have and we all will know in the future.

As for gearboxes, there is less hassles staying with R30 boxes than any others. L20ET boxes have lower 1st, 2nd & 3rd gears than L24E, but have a higher 5th, so I use L20ET boxes for now, but have L24E, RB20DET & a US spec BW T5 for future maybe.

Cheers, D

Link to comment
https://www.sau.com.au/forums/topic/136666-2-part-question/#findComment-2543133
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't like "actual computers" for in car use. They take time to boot up, have OS annoyances, and so on. Arduinos etc are ready to go a few seconds after power on, don't mind being agressively powere cycled, because everything is non-volatile, don't mind being shaken and stirred.
    • As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
    • Being a race car, and being in the era of the Arduino, one would think it would take little effort to build a controller to do the spraying based on a real physical measurment. Waaaaay back in the dim dark AS days, JE "designed" (as in, he had help) a microcontroller based intercooler spray system. It watched the difference between a temp sensor stuck on the core and one in the free air in front of the cooler, and if the temperature difference exceeded a (settable) threshold, it would activate the sprays. Thus, it only ran water when there was an actual need for water. If you stop to think about the actual physical things that are going on in that stack of coolers, there's probably at least a couple of triggering conditions one could come up with, and one could probably even run one pump with more than one solenoid valve, to allow water to be placed where it is needed, or at all points at once (if it is needed at all points). We're in the age of science baby. But.... I suspect that intercooler water sprays are on the forbidden list in most circuit classes, no? So only good for Targa type stuff?
    • I'll just leave this with, holy shit, those cars at work are awesome, and this will look wicked!
    • Could you modify this duct so instead it pushes the extra air through the radiator too and not down and out? For temps, I know it's not the greatest idea, but as a bit of a last resort, you could use a very intermittent misting spray onto the front of the coolers/rad. You don't want to be soaking them such that water is dripping off, but a small most on/off so that the water evaporates. That point of it constantly evaporating, rather than being soaked in water, will pull a LOT of heat out of the cooler. I'm literally thinking just the little mist sprayers for a garden from Bunnings. Being in a low humidity climate it will help even more! The other trick if you want to be ghetto is some shade cloth hung in the opening, and keep it wet. Pretty much now it's acting like an evap cooler on a house, but cooling the air you need to use to cool the radiator...   On a topic to think about too though, when air enters through the bumper, is it all nicely ducted from the edges of that opening back at a nice angle, or is it like most cars, and the edge of the opening just stops, and suddenly it's wayyy wider behind that? If it does the later, get it shrouded out at nice angles. When that opening changes too rapidly, it can actually cause a high pressure zone between the front bar and radiator, and limit air flow into that area, which means less air for cooling, as it effectively stalls the air, AND adds to drag...
×
×
  • Create New...