Jump to content
SAU Community

Recommended Posts

I am planning to change the gear oil in my R33 GTS-T. I have already purchased the 1 gallon lightweight redline oil.

I have an empty 1 litre VMX80 bottle that has a little hose attach to the cap. Can I use this bottle to fill up my gear box without a pump? (some people mentioned to use a pump to fill it up)

:)

Link to comment
https://www.sau.com.au/forums/topic/13827-change-the-gear-oil-without-a-pump/
Share on other sites

  • 4 months later...

Not sure to tell you the truth. I haven't ever tried it this way.

I managed to get a 1/2 inch torque rench to the filler and drain plug. Gave me heaps of leaverage to get the nuts loose. I still almost spat my guts out my bum cause the nuts were so damn tight though !!!

I 'think' you'd have to take the gearstick surround off, then the 4 bolts around the gearstick. Then that might open up the hole which may let you get a hose down there and put it in the filler hole. Then just use a funnel thingy to fill it up.

Just don't spill the oil inside the car !!

J

I think someone was saying that you can fill it up via the speedo cable plug if you can't get the filler nut out.

Just undo the speedo cable and pull it out, then do it that way.

Not sure if you'd be able to fill it up from inside the car if you use the speedo cable way though...

J

guys, the best way to fill it up is : after u drain it from the bottom plug put that plug back then take the filler -level plug out on side of the b/box and use a pump to fill it up ( i use compressed air to pump it up there ). if u want to get to it from the top this is how the gear stick comes out .

take the trim mould off , gearknob off , boot off , ( u need new cable tie to put back )then there is a c-clip that u have to take off ( u need a long nose to sqeeze it )once u take that off the gear stick just comes out .

warning here though u won't know when its full unless the filler -level pug is out but even then if u fill from there i'm not sure that it will go in to the box on gtrs 4wd 's it won't, it will end up in the trasfer case .

don't bother doing it this way besides u should be able to take the plug out so u can check the level everytime u do a service so u must be able to take the plug out .

u need a long wrentch ( like 300 mm ) with a 1/2 inch drive ( or maybe 3/8 cant remember ) its shouldn't be that tight i never have any trouble undoing it .

Read the link

I did this on two cars on friday, one through a stupid little hole and one through the speedo sender.

USE the speedo sender hole instead of the normal filler hole if u cant get it undone like me :) its a hell of a lot easier, and you get the correct level too.

hmm not the same gearbox, but last week i changed clutch and gbox oil in my other car, damn filler plug was rounded off and so damn tight, the only way i got it off was to take the whole box off and weld a long bar to it to break the seal. total pain in the arse!

as for filling it without a pump, get a length of hose (about 3 meters) that is big enough to fit in the filler plug hole but so its loose. and get a funnel. stick these two together by what ever means neccesary.. silver tape works good to seal it.

put one end in the filler hole and the funnel end above the car (may have to attach it to something unless you feel like holding it there) then through gravity the oil will flow down into the box slowly. if you know how much to put in fine just put that in, but if not just keep topping it up untill it runs out the filler hole and then let it drain till it stops then replace plug

how do u know when u have just the right amount if u dont undo the level -filler plug ??

how do u check the level if u dont undo the plug when u do normal minor service ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...