Jump to content
SAU Community

Recommended Posts

hi guys,

over in campbelltown we have a line in trouble..

car starts and idles, will rev out of gear, but if you drive it the engine will cut out with no stutter or shudder just off. It will turn back on and drive another 50m before shutting off again.. what the heck is wrong with his car?

any ideas appreciated. We have checked most things already but cant find anything wrong

Link to comment
https://www.sau.com.au/forums/topic/139254-rb25det-cutting-out/
Share on other sites

Just to clarify it will sort of stutter and shudder especially if revving or attempting to drive. Depends if u have it at low or high revs, which makes no difference except seems to have less chance of cutting out as frequently... but still stutters hardcore. If the car has been left alone for a while this can take a little while to happen. But It WILL cut out as a result of this, sooner if you "try" and drive it.

if you leave the car for a while, ie 30mins + it will start and rev ok but still sutter and choke a little bit... the longer you keep reving it the worse it will get until it gets so bad even if you start it it will die straight away. But the longer you leave the car it seems the longer it will take to get to such a problematic state. make no mistake though, the car is essentially useless.

Thoughts??

Edited by Xizor

If the car has been off for a while u can usually start it and rev it hard for a bit and usually only notice slight stutters in the engine/revs but it will progressively get worse and more frequent until it reaches the point where it will die as soon as u start it no matter how you try and rev it.

Search for how to throw the R33's ecu in to diag mode. It will then output any faulty sensors. Hopefully. :D

The fuel and afm check you may not be able to do by the sounds of it... Might be worth dropping it off to some one who knows these cars as no doubt they will find the issue quick smart.

Mate i cant drive the car anywhere really and ripping the ECU out is a bit of a last resort hehe

I'll run some diag software on it via laptop tomorrow afternoon and try and replace fuel pump and see how we do.

Anyone know how to drain fuel tank? That might be worth doing too.

What good is putting it in diag mode? doesnt it needed to be hooked up to a nissan computer or something??

I dont even care about cost anymore i want it working.

Nope, you throw it in diag mode and it runs its tests and throws out a code (by flashing a light (dash light or light on the ecu). You count the flashes and then compare the number to that in a list. It then may show something like code blah... coolant temp sensor or code blah afm etc etc..

You can even throw it in an o2 test mode where it flashes the light as the o2 sensor goes high/low. An easy way to determine if your o2 sensor is shagged, lazy, or not.

i had a problem with my RB20. all stock except an exhaust and pod. it would start and run fine when it was cold, but once it warmed up it would just cut out, altogether, then not start again for a while until it cooled down. I found the problem to be my alternator/power supply. Might be worth checking.

does the engine kick over every time you start it? either hot or cold?

Yes. But if ive had the car on for a while reving long enough or attempted driving it it will reach a point where it will cut out as soon as its kicked over. almost as if its using fuel thats flowed through due to gravity but ran out. ignore me lol

It doesnt normally just straight cut out due to temp, it struggles and hiccups like a dirt bike with its fuel ratio/mixture wrong except will also cut out like its not getting fuel and then just not go at all. then repeat process after a while.

Edited by Xizor

yeah rob thats why i said i would pick up 2 filters, one for mine and one for yours. The whole thing ith the gtr filter had me wary, i was going to swap mine in the other night but pefer daylight. and als your brother is a tool lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...