Jump to content
SAU Community

Recommended Posts

Hey guys i just want to find out from you guys who have the same car (and only you please) with the standard pump, how long it primes for in the morning or after many hours of not running. If you don't start the engine when the ignition switch is turned to 'ON' how long do you hear the pump prime for? Is it very loud? And lastly do you ever hear the same prime noise for a very short time (1 second) during prolonged idling? ... memory this too is only after the first start in the morning or after many hours as previously mentioned.

Many thanks,

Deren

Yeah cheers for that mate. How about the prime during idle?

BTW just realised your after a nissan boot badge, i dont think i will be using mine anymore so its yours if you take me off your bad trades lol!

Edited by Godzilla32
Hey guys i just want to find out from you guys who have the same car (and only you please) with the standard pump, how long it primes for in the morning or after many hours of not running. If you don't start the engine when the ignition switch is turned to 'ON' how long do you hear the pump prime for? Is it very loud? And lastly do you ever hear the same prime noise for a very short time (1 second) during prolonged idling? ... memory this too is only after the first start in the morning or after many hours as previously mentioned.

Many thanks,

Deren

The sound came on due to lack of lubrication in the fuel pump, you can either put Redline SI-1 in your petrol tank or buy some ashless motorbike 2T, added 50-100ml and it will do the trick.

Edited by Trex101

Not on the GTR. I just cleaned the TB on my Mazda's KG 2.5L V6 and it ran like crap quite some time... next time I wont be lazy and I'll take the TB off rather than just spray all that carby cleaner down its neck :)

Is it a tough job? I'm sorry about dragging things off-topic, but my plan is to clean the IAC, clean the TB and then if it is still high I'll adjust the trim pot on the ECU. I'm pretty sure it had an aftermarket ECU removed prior to export, so the problem could be there...?

Dont clean the throttle bodies, It wont make it any lower, only higher, the more you clean from around the butterflies the more air gets thru when they are supposed to be closed - Hence high idle. Prolly the idle control valve getting stuck. Good place to start anyhow :laugh:

Dont clean the throttle bodies, It wont make it any lower, only higher, the more you clean from around the butterflies the more air gets thru when they are supposed to be closed - Hence high idle. Prolly the idle control valve getting stuck. Good place to start anyhow :)

Very good point dude! Cheers

Thanks guys. Sounds like i have no problem then :)

Its not the attesa pump. There would be no need for it to operate at idle. Only works when you are locking up the clutch packs in the transfer case to provide front torque.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...