Jump to content
SAU Community

Recommended Posts

Rebuild on a RB26 will set back around the 7k depending on what you put in of course-it could be a lot higher with really good gear (like 12K)

There are 32GTR's with running engines around for 18k now...market is dead...sux

dennis lives in sydney, hills district! i know this car and can vouch for it being very tidy! sorry to hear about the big end mate! best of luck with the sale!

cheers Garth

12 is way 2 low, 15 is the lowest people,

it mite have a spun bearing but go buy a stoccka and mod it like i have mine,

im loosing 10 grand if i sell it for 15000,

turbos cost me 3000, clutch cost me 1200, coilovers cost me 850, apexi power intake kit cost me 200, and now yous can add it up and see what it owes me and how much yous would be up for modding a stockka, and these prices are without labour

turbos r&r is nearly 1000, clutch was 550, and coilovers were 200 this was labour,

here is nearly 7 grand in mods fitted to the car, so if some1 buys this for 15000 and builds the motor they have gotten themselves a gtr wiv a new forged intrenaled motor for around the 21 22000 mark,

all that would be needed then is a computer and a fuel system, the turbos and clutch r good for 10 sec passes...

sorry people but 12000 is a nooo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...