Jump to content
SAU Community

Recommended Posts

Hi Guys,

I have recently been having problems with my 32 gts-t. Basically under hard/full acceleration the car was flat spotting where it felt as though petrol was not getting into the engine properly around 4 - 5.5 thousand rpm.

First my mechanic tried a fuel additive which seemed to fix it but then it slowly returned. Then got the injectors ultrasonic cleaned. Again, seemed to fix it despite the fact that when i got it back the car had serious problems starting which it still does. 2 out of 3 times i hold it on start while its turning over and over and doesn’t come to life. After a second try it splutters into life. Now the flat spot has returned again.

It has cost $300 with additive and injector cleaning so far and back where i started. Also, it also does not idle well, specifically when pulling up to lights and selecting neutral while rolling to a stop the revs nearly drop to 0-100rpm. I stop and it comes back up, goes down, up.....

I have a feeling from what I have read on these forums that the problem may be related to the AAC valve but I would appreciate anyone who could offer any advice.

Thank you in advance!

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/
Share on other sites

chked ur fuel pump?

Yeah that was one of the next things I felt could quite likely be a cause of the problem. But I was wondering if the AAC valve is (and im not sure if this is so) causing the idle issue could that have any relation to the flat spot?

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2603706
Share on other sites

You haven't stated if the engine has been modded in any way. Info like that is often useful in diasgnosing these sorts of problems.

Idle "hunting" is likely the AAC valve - it's the little cylinder attached to the back of the plenum chamber.

The flat-spot is totally unrelated to the AAC valve. It is likely the ECU is detecting "knock", which may be caused by a dying fuel pump. Get the car onto a dyno, with an AFR meter and a fuel pressure gauge.

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2603857
Share on other sites

AFR = Air Fuel Ratio.

There isn't a meter for this in the car.

The car monitors Air flow = AFM (Air flow meter)

and from this and other factors (tps etc) determines how much fuel to put into each cylinder at various revs/load etc.

The car also has a o2 sensor which tells the car essentially if the car is running rich or lean.

If you want a proper AFR you'll need to get a wide band AF gauge and probe. Very good tuning tool, lets you know exactly whats going on with your AFR's.

You know when you see people getting their car tuned on a Dyno, and they tuner's got a probe sticking in their exhaust? This is what that is.

Sounds like your problem is fuel issues, either too much or too little.

Generally the more mods you do to a skyline the richer they run. Richer=safer (away from detonation) but also means retarded as far as power use goes, and fuel economy goes down.

It could also be fuel starvation= Ie, dying fuel pump, blocked fuel filter etc.

This is the most dangerous of all senarios, if this is the case, get it fixed soon.

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2605760
Share on other sites

Thanks for the replies.

It's all very confusing. Im a bit worried now, I will have to minimise my use of the car from now on cause I am really busy with uni/wrk so cant get it looked at atm. The only day I have to use it is wednesdays, every other day i can get lifts/use another car or p/transport.

At least I know a few things it could be know. I hope i can find out for sure what the problem is.

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2607780
Share on other sites

Just to add to that,

When I just drive the car normally (as in not rev beyond 3,500rpm) it is 100% fine and drives smoothly and without problem, other than the issue of getting it started... So this wednesday and next I assume that it wont be doing any damage driving like this??

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2607825
Share on other sites

Guest tosboost2

ok to start i know on this forum that this guy says do this, and another guy says do that. so i dont care if u listen to what i have to say

but anyways i had the same problem with my 32.

i spent 600-700 bux diagnosing the problem and changing things, taking the car places etc.

it ended up being my afm was dead, so i got a new one, and the seal around my blow off valve was busted, i dunno how that made much difference but i fixed that, i still have a few problems but only when the cars cold, which is the cold start valve. and seeing as i cant find another one ill have the problem for a while.

find someone else with the same afm as you and just swap them over and see if that helps :laugh:

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2621547
Share on other sites

ok to start i know on this forum that this guy says do this, and another guy says do that. so i dont care if u listen to what i have to say

but anyways i had the same problem with my 32.

i spent 600-700 bux diagnosing the problem and changing things, taking the car places etc.

it ended up being my afm was dead, so i got a new one, and the seal around my blow off valve was busted, i dunno how that made much difference but i fixed that, i still have a few problems but only when the cars cold, which is the cold start valve. and seeing as i cant find another one ill have the problem for a while.

find someone else with the same afm as you and just swap them over and see if that helps :)

Thanks for your help, my mate has a 32 gts-t like me, so I can try that then and ill put in a new petrol filter if that doesnt work and see...

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2622517
Share on other sites

  • 3 weeks later...

Well for those who are interested... PROBLEM SOLVED

After being introduced to a friend of a friend, we got talking, and I found out he owns an r32 gts-t also, and is a mechanic!! He had rebuilt his rb20det and knew a lot about them.

Took my car to him and he discovered a pipe connected to the fuel pressure regulator was split in 2 places and barely hanging on. Replaced that and he raised the idle and it was fine, revvvvs out beautifully and sits perfect at 800pm at idle and doesn’t fluctuate.... all this fixed for next to nothing, meaning the $300 spent to date was wasted... at least its fixed !!!!! :pirate::):yes:

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2671185
Share on other sites

which "pipe"

can you put up a pic of an engine bay and point to it?

cheers,

Warren

PS did it also help with the starting issue?

Yeah its pissing down outside now, but next available chance i will take and post pic, and yes it had serious issues starting sometimes, others it would be fine, but more often than not id have to try 2 or 3 times... all good now :P

Link to comment
https://www.sau.com.au/forums/topic/139666-rb20det-dilema/#findComment-2671595
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...