Jump to content
SAU Community

Recommended Posts

  • Replies 78
  • Created
  • Last Reply

Top Posters In This Topic

Actually they stopped allowing runs at 11:15pm because well... they felt like it. So 2 of 2 nites that the weather was fine they ended the night early because well... they felt like it. The other nite it was rained out 1hr 20 after the nite started so of 15hrs racing we've seen 7hrs.

Edited by benm
Link to comment
https://www.sau.com.au/forums/topic/140333-wsid/page/4/#findComment-2684760
Share on other sites

NismoGod you got 13.45 with only full exhaust?? What other mods man??

Thats awesome time for just full exhaust.

I got full exhaust and my best was 14.10 at 100MPH but on street tyres

But my launches were really crap but.. Need more practice!!

Link to comment
https://www.sau.com.au/forums/topic/140333-wsid/page/4/#findComment-2684785
Share on other sites

siddr20 yeah i got a 13.426 on semi slicks. 60ft 1.997 and 103.5 mph. i have a full turbo back exhaust. its a split dump pipe with 3" system with a 5" hi flow cat. no other mods except a pod. but i really can only take what the previous owner told me. he imported it april 06 and did nothing with it, so maybe something else has been done, but i doubt it cause the power isnt too huge. i did a 13.700 on my 19" which has a 60ft 2.018 at 102.5 mph. there is still some time with the current setup will the slicks, hope to drop another .1-.2 off the time. the more time i go to the drag the quicker im getting so time will tell.

Link to comment
https://www.sau.com.au/forums/topic/140333-wsid/page/4/#findComment-2685345
Share on other sites

heheh man i was hoping to get into the 13s to be honest..

I knew i could do it!! i was so close!!

Just wish my launches were better!!

Its all about the launches to be honest.. Only mods i got is ful exhaust (spilt dump also) and pod..

I only had 7 runs, so maybe next time i can get into the 13s..

very impressive with your times btw!!

and yes im jealous!! :D

Link to comment
https://www.sau.com.au/forums/topic/140333-wsid/page/4/#findComment-2691760
Share on other sites

Nothing special their tonight except a Cobra, everything else was either a regular or just a VX Commodore bashing in the 13's.

I got to the drags at about 6:45pm and it was 36c, 20mins later it was 23c and so windy I thought the big undercover area at the top was going to lift out of the concrete and blow away.. how crazy is that.

Edited by benm
Link to comment
https://www.sau.com.au/forums/topic/140333-wsid/page/4/#findComment-2695584
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
    • street use or race track, what hose size and why? what factors change with the hose size options ?   see most comon is an10. when you see most oem external coolers are closer to an12? does high volume oil pump like nitto need an12 or 10 be just fine
    • The rod I was moving left and right you can see looking from the passenger side floor up into the center console.  IMG_8095.mov
×
×
  • Create New...