Jump to content
SAU Community

Recommended Posts

Just today my Stagea has developed an intermittant miss when at idle.

It only seems to be present under 1000rpm. The wagon also seems to be using noticeably more fuel.

I'm thinking it's a coilpack, but I did drive it a distance with the low fuel light on and it started after that. Maybe it sucked some crap up from the bottom of the tank.

Could it be a partially blocked injector? Would that explain the higher than normal fuel consumption?

Also, wouldn't a stuffed coilpack cause a miss all through the rev range?

Anyone had similar and can help?

Link to comment
https://www.sau.com.au/forums/topic/140430-intermittant-misfire-at-idle/
Share on other sites

I dunno, personally I have had a blocked fuel filter because of gunk and it didnt cause a miss. Never heard of an injector being blocked, but sounds plausable, SK?

If the coil pack was tottally dead then it wouldnt be firing at all, but if it was intermittantly firing then it would get worse as the rpm gets higher, wouldnt it?

But either way I couldnt see any of the above affecting fuel economy that much..............?

ya my car does the same thing.. pretty sure its using more petrol 2 :)

I was told the missing is because my plugs are at 6.x mm or something like that.

She's fine when you drive though, doesnt miss at all..

I had a look at my coilpacks last night, they looked pretty good.. not that i no what im realy looking for though :)

I did have a similar problem with misfiring but my engine stalling and it stuggled to drive at all most times. It ended up being the Air flow meter in my case. It seems to be running well now that I have replaced it. I am about to take it for a drive to Coffs Harbour next week so I should find out if there are any gremlins left.

Gap the plugs to 8mm. Coilpacks are a common problem. They are usually fine down low and start to struggle up high. I dont if the reverse is possible.

Its one of those how long is a piece of string problems. Get it on the dyno!

  • 2 weeks later...
  • 1 month later...

darnit...my wagon started to develop the same missfire at idle...driving seems fine...think its bad but my safc is doing some correction...raised the boost to 10psi and gave it a good revving ....missfire seemed to have dissappeared for now....it started after a normal cruise to canning vale via tonkin n roe....temp outside was quite warm so i dont know if its temp related.

hope its something easy to fix like plugs...or worst case air flow sensor and not a stuffed valve :(

Finally got the whole problem sorted.

After the burnt valves got replaced, it still had a slight (but less dramtic) misfire. The mechanic could not replicate it, so I took him for a drive. The miss also came in under high rpm/load. I nailed the car, and sure enough at about 4500, it started missing and felt like it hit the rev limiter.

They took the coil packs out and got them tested, all 6 were f%^&ed. Replaced them all, car runs sweet as.

On talking to the mechanic, it turns out that my engine was overboosting because of a stuck wastegate. This caused it to be a bit lean (as well as the stuffed injectors) and burnt the valves. This hid the other fault of the coilpacks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...