Jump to content
SAU Community

Recommended Posts

To be honest while i love the rb motors...you cant go past the fact the 1j and 2j have more potential, without having to replace more.
lol your a mechanic work its out :P

you might want to actually back up your statements on here before making up such bullshit.

but please do tell us how you did come to a conclusion the 1j engine is somewhat a better engine then the rb26?

and do remember... your talking to people who know somewhat 10x more about this kinda stuff then you do.

what is with you and getting a kick out of searching this thread for my posts? seriously dude...get a life much?

And if you so called know 10x as much as me about these cars then you should know that the 1j and 2j have more power at the engine then what a rb engine does when it has stock internals.

Comparing power to anything but the engine is stupid because they come from cars with different set ups the closet you can go is the RB25 and the 1j seeing that they are the same displacement and both drive RW drive car, the closet you can go to comparing the rb26 to is the 2j which in that case has completely lost.

I am NOT referring to a fully modified engine, and the first statement you quoted was in fact referring to the 1j against the rb25 as at that stage there was no mention on a rb26 at that stage in my posts.

If you didn't know that i suggest pulling you head out of the dark psychotic midst its in, shutting your mouth and do something good for yourself and research.

plus a person who knows 10x more about cars then myself, would know how to not blow a RB26 engine.

That is all i am going to say in reply to this and if you wish to take this further email me.

Edited by 000DNK
plus a person who knows 10x more about cars then myself, would know how to not blow a RB26 engine.

That is all i am going to say in reply to this and if you wish to take this further email me.

since this "person" replying knows so much about the rb26, you'd know by fault that the big end bearings go within the rb26 engines hence they blow easy. bawahahahahahaha

90% of rb26 engines are rebuilt because of the big end bearings otherwise they are modified before they blow.

RonaldMcGTFO.jpg

btw, i read through this thread daily.

just found what you posted to be funny.

Another reason why the 1jz and 2jz have more potential without having to replace more as i first stated :bunny:

i would also appreciate if you would cut the language out as there is no need for it and i do find it quite offensive.

Edited by 000DNK
Another reason why the 1jz and 2jz have more potential without having to replace more as i first stated :bunny:

i would also appreciate if you would cut the language out as there is no need for it and i do find it quite offensive.

LOL!!!!

The 2jzhas the potential to anything like any engine but at the same time, it still needs modifications done just like any other engine to get its power figure. a rb26/30 has the ability to produce something of the same power a 2jz engine does.

LOL

you need to do some more researching.

just been reading though this, and i noticed a comment "ohh and btw... the gearboxes in the 2jz and 1jz can't handle the power figur a rb25 can handle" quoted by Jjay, believe it or not the R154 can handle in excess of 500rwhp without a single modification, and the V160 and V161 supra 6 speed boxes don't need to be modified until 850+ rwhp, whereas the humble RB25 gearbox will start throwing 1st and second gear at about 400rwhp. back to the drawing board i think. my 2c worth

Farrk me what a shit fight...here we go again.

JJay and Andrew, both w58 and r154 toyota gearboxes have there issues, and so do Rb25 gearboxes,It goes to how you treat them,(flat changing is not really good for any gearbox for that matter) not necessarily how much power you are putting in front of them BUT how much torque , you know the stuff that makes your engine twist when you blip the throttle on idle??

You can run way more than 400hp on a rb25 gearbox...Many of you may not know that they have the same bearing diameters as GTR gearboxes, but with less grip of a 4wd car they are quite strong in a rear wheel drive car.

A Rb25 gearbox is basically the same as a GTR box but without the transfer case.

The Toyota boxes aren't too bad either, but they tend to get a broken washer or shim in them which causes gearbox to jam, a factory fault i believe but makes it worse even with minor hp increases .

The Getrag 6 speed is the ducks nuts for toyotas, can withstand coupious amounts of torque and power, but once again how you treat it is a major factor.

So anyone going to the track day on saturday at willowbank? I am but not racing,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...