Jump to content
SAU Community

Recommended Posts

Ok heres there story.

I tried to install my pioneer cd deck into my R32 GTS-t.

Me and a friend have done many stereo installations before.

When we first installed it, we blew a fuse that controlled the dashlights/tail lights.

Thats ok, we found the culprit wire(s) and sorted that out. No more fuses blew.

From then when I turned my car off, the doors would lock and when I clicked the button on the immobiliser, it would unlock and re-lock again.

So we ripped the whole deck out and detached everything from the wires. So now there is no wires connected to anything. When i turn my car off, it unlocks the doors. So i will hop out, lock the doors and go. Now when i return to my car, the immobiliser is armed, i click the button and it will unlock the doors and then lock straight away. The only way to get in, is to use the key.

When the immobiliser is not armhated, the doors will lock fine.

I have spent many many late nights and very many hours trying to solve this problem. We went through and pulled apart all the relays and tested them. We also swapped over the immobiliser with a friend (same type) and the problem was still there.

So our guess is, there is some wire(s) that were connected to the back of the stereo that either need to get power or need to be ground.

Another point is when you click the immobiliser button, it doesn't flash the parkers/tail lights like it use too.

Can anyone provide any help on this?

I have gone through most of the wiring and i know what most of the stereo wires do. However there are still wires there that we don't know the exact purpose for.

Any help would be greatly appreciated.

Yes, thats an option.

But those guys are ****ING DODGY!! and i mean very dodgy.

When we were going through my car, we found wires spliced and left like that. Things butchered here and there.

Guy i work with decided to get them to do his tint.

They ripped the back shelf out, and wrecked all the terminals. Also broke the shelf. At first they claimed they never touched the shelf, then they said, they just pulled it forward a little.

They're not someone i would like to trust or do business with.

Go through all the fuse's with a test light and ensure that they are all ok, next check that all earth wires to the alarm module are grounded

(HINT: some alarm installers use the radio as a ground)

some alarms use a seperate module for the door locks check this aswell.

When i fitted my alarm I used the wires going to the hazard switch did you plug it back in? as mine would not flash if the switch was not pluged in.

Thats all I can think of for now check all of the above and let us know how u went.

if u have more info that would help me tell u what to look 4!

Thanks for the offer rob, but i'm in WA :D

DAMQIK, Done just about all the checks you can think of.

I though i posted everything in the first post, please let me know what i missed out.

It doesn't have an alarm. Factory central locking and a Cyclops paralyser immobiliser.

I have a mate who was an auto elec for a few years, i'm trying to get him to have a look, but hes just been busy.

Soon as i sort the prob out, everyone will know!!

Thankyou everyone for your imput.

Ok so you checked the fuses under the dash? under the black cover under the bonnet & next to the battery? (there are 3 Fuse boxes in a r33)

PM me your email address and I will send the wireing diag 4 jpg pictures.

Thou I feel your prob is bad earth maybe run a new wire from earth to the module and the same for power+ if you have not yet tryed this.

is your cig lighter getting power?

Ok, I feel like a dick.

All along i knew the problem was easy, but just kept missing it. Mainly because each time we were working on it, it was between the hours of 10pm-3am.

There is a relay down in the kick panel with a "door lock timer" module, somebody has taken a wire off that relay and put it back on the wrong terminal, plus the immobiliser had a blown fuse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
×
×
  • Create New...