Jump to content
SAU Community

Recommended Posts

on a start up there is a weird knock in my motor when its warm it goes away.its kinda a yuk and scary noise..i will start my car in the morning and get this weird knock rattle noise at idle which is scary..anyone have the same noise and what it is..my car has only 80klms on the clock..any ideas cheers fellas

Link to comment
https://www.sau.com.au/forums/topic/142453-weird-knocknot-sure/
Share on other sites

Most likely you are describing lifter noise.

Read this: http://en.wikipedia.org/wiki/Hydraulic_lifters

"Frequently, the valvetrain rattles loudly on startup due to oil draining from the lifters when the vehicle is parked. This is not considered significant provided the noise disappears within a couple of minutes, although typically it usually only lasts a second or two"

Normally I would be wary of what is on wikipedia, but this information looks to be fairly correct.

Try using a thinner oil, that should help the noise to go away faster.

i doubt it will be lifters if the noise sounds so bad that it concerns you. as for lifters my mate wacked some additives made for sticky lifters which has reduced the ticking noise dramatically.

oh yeah my other mate and his wrx had something similar. loud as ffff rattle turned out to be one of his timing belt pulleys shearing/wobbling itself off. luckily we picked it up in time before it completely fell off. have a look =)

Edited by (B1) MR_fanny

Lifters (or hydraulic lash-adjusters as they are more correctly known on, non-RB26, DOHC powered 'Lines) don't 'knock', the sound they make is more of a sharp 'ticking' noise if they are low on oil pressure (thats your valves hitting the seats more harshly).

A dull knocking is likely to be more serious. Just get a mechanic to have a listen with a diagnostic stethescope.

can the rockers be adjusted on a rb25 at all as my sons car has some lifter noise if not any idea on how much a set of lifters is worth ?

cheers

RB20/25/26's don't have rockers (unlike SR20/RB30/L-series engines), the cam lobe acts directly on the lash-adjuster, which controls the valve opening/closing.

Engine oil flush may clean up the supply galleries and make them run quieter, but if your son is prone to thrashing the car, they will often sound tappety as they "pump up" with high oil pressure and increase the valve clearances.

Become a member of the club and give Lincorp spares a call if you want to purchase new ones.

Cheers :(

yeah its a bit weird.it deffanatly has some thing to do with oil i hink..when i rev it off idle the noise goes straight away which im guessing cause if the oil pressure build up.its deffenatly a knock not a tick if you no the diffrence between the noises..its deffanatly not normal and never use to happen..ill try a good flush and maybe get a good mechanics view on it..any one recomnd any places around the parramatta area..cheers guys

  • 9 months later...
yeah its a bit weird.it deffanatly has some thing to do with oil i hink..when i rev it off idle the noise goes straight away which im guessing cause if the oil pressure build up.its deffenatly a knock not a tick if you no the diffrence between the noises..its deffanatly not normal and never use to happen..ill try a good flush and maybe get a good mechanics view on it..any one recomnd any places around the parramatta area..cheers guys

What was the result of this?

Cheers

Dazzzler

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...