Jump to content
SAU Community

Recommended Posts

bad bad bad!!

is it from the radiator? or from the block?? If it is from the block it could be a busted head gasket and its going to cost big $$$ If you continue to drive it you will warp or crack the head resulting in even bigger $$$

If you are lucky.. it is just busted radiator, or split radiator hose. Not that you should be driving it in this condition, but pop the bonnet.. you should see steam shooting out from somewhere - which will narrow it down. If you are lucky it will just be a hose.

My recommendation is not to drive the car at all until you can work out the problem. It most likely is quite serious.

Temperature problems can be FATAL to an engine..especially a modern engine.

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296076
Share on other sites

got your PM pred and thankyou for your help... damn, now im shitting my pants, don't know where exactly it is leaking.. i looked under the car and it has the black shield covering under it so i couldn't tell whether it is the hose, or the block but it is defintely 100% coolant(green liquid). Just went down to the local mobil petrol station and brought some radiator stop leak treatment bottle.. going to add it and hope it helps.. :D:(

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296330
Share on other sites

Guest RedLineGTR

Check the hoses, or remove the cover. Just follow the hoses down to where they end like the bottom one see if there is any fluid leaking. Best Bet is jack it up and take the cover off. I could be the water pump (how many k's) some of them go early before 100k. Or could be a cracked radiator as suggested above. (which is alot less common).

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296580
Share on other sites

I'll put money on it being your water pump. Check the water pump, there is an inspection hole that will allow coolant to slowly leak when the pump seals shit themselves (telling you it's time to replace the pump). With the undertray in place you'll never be able to pin-point the source of the leak. The tray comes off easily.

If the pump is the cause you're up for a new one, & you may as well replace the timing belt while you're there. You need to take the same bits off - so why do it twice?

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I very much doubt it'll be a major problem, so don't stress too much :)

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296690
Share on other sites

Originally posted by pushead

I topped up the coolant in the white bottle as well as the alternator last night

Alternator - coolant? WTF! Coolant & the alternator don't mix well dude!

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296695
Share on other sites

Originally posted by whatsisname

Alternator - coolant? WTF!  Coolant & the alternator don't mix well dude!

???? so you put water instead of coolant in the alternator? i followed a black hose which goes to a white bottle(the backup bottle) which labels coolant.

Checkout the attached Picture:

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296768
Share on other sites

you lucky bastard :D with the temp that hot ur lucky nothing blew

mine ran hot once and blew the seals on the plastic radiator end tanks - goodbye radiator

the water pump is a c*** to get off cos of the crank pulley bolt. you will more than likely need a rattle gun to get this off

the water pump may not be dead, it my just be the seal, in which case pull the pump off, put new sealant around it (doesnt use a gasket) and put it back together

you can drive around with a leak BUT make sure u keep the system topped up

if it starts sucking air or depressurises it will overheat again and u may not be so lucky

take it to a mechanic and there are pressure tests you can do on the radiator so check for a leak/crack. you can also run a test to see if there are exh gases in the system (leaking head gasket) so you will be able to pin-point the problem

just finally, cooling systems are ****s to work on and fix, if youre going to repair it make sure u do it right cos its the kind of thing which if not done properly will cause alot of headaches

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-303732
Share on other sites

Originally posted by whatsisname

I'll put money on it being your water pump.

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I would say this is invaluable advice.

Our pumps are cheap which is good.

You want to do pump, timing and accessories belts at once to save labour.

$150 for labour is damn cheap though.

T.

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-304054
Share on other sites

I paid $350ish (think it was 350? Certainly under 400) for a new genuine Nissan w/pump & timing belt. Both installed. Thanks Vince (Rigoli).

I didn't want to take any chances so I got them both done. That way I knew they were new :)

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-306926
Share on other sites

Originally posted by whatsisname

I'll put money on it being your water pump. Check the water pump, there is an inspection hole that will allow coolant to slowly leak when the pump seals shit themselves (telling you it's time to replace the pump). With the undertray in place you'll never be able to pin-point the source of the leak. The tray comes off easily.  

If the pump is the cause you're up for a new one, & you may as well replace the timing belt while you're there. You need to take the same bits off - so why do it twice?    

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I very much doubt it'll be a major problem, so don't stress too much :P

Thanks for your detailed info dude.. really needed it...yep. same as the RB30 VL pump.. what hole are you refering to which you can tell the water pump shit itself?.. i couldn't seem to find it.. is it near the fan belt?

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-310998
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...