Jump to content
SAU Community

Recommended Posts

Hey Guys,

Im a new member from Toronto, Canada

Just had a quick question, i have a 1991 r32 GTR, and recently the 4wd light came one, and i get a code 20?

does anyone know what the code means?

appreciate all the help i can get!!!

Thanx!

Link to comment
https://www.sau.com.au/forums/topic/146165-4wd-light-problem-wcode-please-help/
Share on other sites

Hey Guys,

Im a new member from Toronto, Canada

Just had a quick question, i have a 1991 r32 GTR, and recently the 4wd light came one, and i get a code 20?

does anyone know what the code means?

appreciate all the help i can get!!!

Thanx!

ok i figured out that code 20 = ETS solenoid or circuit

BUT now i dont know what to do :laugh:

ANY HELP would be apprecaited!

Good news and bad news

the GOOD

checked the pump NO PROBLEM!

check the ECU and switched it with another one NO PROBLEM

BAD NEWS

still get the same code...

Im frustraded!!!!!!

after looking at the skyline manual it was to do this

"Remove ETS actuator relay connector and turn ignition

switch ON. Measure voliage between body harness

connector terminals "

Where is the ETS actuator????

thank you for any help

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...