Jump to content
SAU Community

Recommended Posts

I guess it had to happen.

The combination of:

"Adequate" power (578 rwhp)

Good torque (HKS 2.8L kit)

Sudden power delivery (GT-RS terbs)

Rebuilt transfer case

Low ratio diff gears (GTS-4 CW&P)

is now resulting in some serious torque steer when coming on boost.

I'm thinking that a front LSD (say 1.5 way) will improve things, however will this adversely affect steering?

"Plan B" may be to adjust how boost and torque split is delivered? I have a dual solenoid boost controller fitted and Duncan's ETS controller available (not fitted yet).

Thoughts and recommendations?

Link to comment
https://www.sau.com.au/forums/topic/146528-serious-torque-steer-in-gt-r/
Share on other sites

Hi Gav,

my R32 GTR came with mechanical LSD front and rear so i don't know what make or spec level they are but i've had no probs with torque steer or any other steering problems. It can be a little clunky, through the steering wheel and you can hear it, if taking tight corners and using enough throttle to make the wheels spin. I'm only running about 360 HP thou.

I also have an ETS controller but it can't reduce torque split to the front only make the torque split come on earlier which if yours is the same may make your problem worse.

The LSD up front makes for awesome traction, after warming up the rears at the plex i was able to do 8k limiter launches with very little wheel spin, that's with 285 street tyres all round. Towards the end of the night there was no wheel spin at all but i suspect that was the clutch slipping as the twin plate has a few problems at the moment.

If i had to get new diffs i would probably get the OS Giken super lock diffs, they come with 14 clutch plates per side. Doubt you would be able to get them in the GTS4 ratios thou.

What gearbox you running with all that HP?

You on R&R from Bulgaria at the moment?

cheers

Paul

Hi Gav,

my R32 GTR came with mechanical LSD front and rear so i don't know what make or spec level they are but i've had no probs with torque steer or any other steering problems. It can be a little clunky, through the steering wheel and you can hear it, if taking tight corners and using enough throttle to make the wheels spin. I'm only running about 360 HP thou.

I also have an ETS controller but it can't reduce torque split to the front only make the torque split come on earlier which if yours is the same may make your problem worse.

The LSD up front makes for awesome traction, after warming up the rears at the plex i was able to do 8k limiter launches with very little wheel spin, that's with 285 street tyres all round. Towards the end of the night there was no wheel spin at all but i suspect that was the clutch slipping as the twin plate has a few problems at the moment.

If i had to get new diffs i would probably get the OS Giken super lock diffs, they come with 14 clutch plates per side. Doubt you would be able to get them in the GTS4 ratios thou.

What gearbox you running with all that HP?

You on R&R from Bulgaria at the moment?

cheers

Paul

Hey Paul

not back until mid Jan, but just some feedback from the tuner and others that have driven the R since the most recent tune and gearbox/tranny case rebuild.

Running an OS cross mission gearset in a rebuilt R33 box.

Won't be buying anything until I've had a chance to look at how it is in real life and perhaps what I can do with boost delivery and/or ATTESSA controller.

Cheers

Gav

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...