Jump to content
SAU Community

Permits

phenline

By phenline,
in Western Australia

 Share

Recommended Posts

phenline Mentor

phenline

Posted
Posted

hi guys

iam a new memeber (as you can probably see) and recenlty purchased a new r33, last night i was stopped by the police and they asked me if i had a permit for my BOV nothing else just BOV. I explained this was a new car and what have you to them and they where very nice and told me to get it looked at at let me go. Now how do i go about getting a permit? any information at all would be nice.

Thanks :laugh:

Link to comment
https://www.sau.com.au/forums/topic/147370-permits/
Share on other sites
GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

You can going to any of the licensing centers and request a permit for any aftermarket modifications, but beware they may not pass your car.

If the BOV vents to atmosphere then you may have issues getting a permit, depending on ow loud it is and who you get.

Best of luck.

Link to comment
https://www.sau.com.au/forums/topic/147370-permits/#findComment-2750358
Share on other sites
bubba Grand Master

bubba

Posted
Posted

My car came with permits, one item listed was an aftermarket PLUMBACK bov. I am replacing the atmo bov that it came with a stock one this weekend just to avoid any yellow hassles in the future.. it's damn loud and I know the cops frown upon it.

When you say they only asked about the BOV and nothing else.. what else is there? do you have a fmic? exhaust etc? if so I'd get these thrown on the permit at the same time, not all of the boys in blue are that friendly..

Link to comment
https://www.sau.com.au/forums/topic/147370-permits/#findComment-2750375
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...