Jump to content
SAU Community

Recommended Posts

Whats the layout?

3 letter 3 number?

Yeah.

The $400 ones, I'm not paying 2g's for a plate - lol

You can have:

3 letters / 2 numbers

2 numbers / 3 letters

3 letters / 3 numbers

3 numbers / 3 letters

Edited by R33MidnightRacer
Link to comment
https://www.sau.com.au/forums/topic/147627-new-plate-ideas/#findComment-2755253
Share on other sites

I've tried to many like that Brent.

I've tired almost everything ..lol

SXC-033

HOT-033

QIK-033

QIC-033

MRR33

Umm..heaps of others too, just gets harder and harder to come up with a good pplate cause they're all taken.

Link to comment
https://www.sau.com.au/forums/topic/147627-new-plate-ideas/#findComment-2755255
Share on other sites

wpn.033

yld.33

wkd.033

cmy.33

aar.33

theres heaps mate u just need to be creative and mix and match

Hehe, I know there are so many you can come up with, mix and match etc ..but sadly all the ones you posted have been taken, just checked them all on PPQ.

Link to comment
https://www.sau.com.au/forums/topic/147627-new-plate-ideas/#findComment-2755263
Share on other sites

give me the link for the site and i will look up some plates for you.

if theres 1 i find i will post it up,

reason im bored and theres nothing else for me too do but sleep and its way too early for that ;)

lol - fair enough.

The website is http://www.ppq.com.au.

Go to "Create A Plate" at the top of the page, and then use "Personalised Plates 3x2" and "Personalised Plates 3x3" as they're the ones from $395. Other ones are much more sadly.

Link to comment
https://www.sau.com.au/forums/topic/147627-new-plate-ideas/#findComment-2755267
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...