Jump to content
SAU Community

R33 Gtst 4 Pot Caliper Parts

bodgie_luigi
 Share

Recommended Posts

NS2500 Experienced

NS2500

Posted
Posted
easily obtained from Nissan Service Parts

the guy printed out the schematics and part numbers for R32 Type M calipers for me

It wasn't easy from my local Nissan parts - they wouldn't help me out unless I had a/the VIN of the car to start the search - all I have is the 4 pot calipers, presumably from any R33 turbo - I don't think the calipers changed at all?

Does anyone know of a good Nissan parts dealer in Melbourne? Or - could anyone help me out by giving me a VIN to reference against?

Eug Grand Master

Eug

Posted
Posted

post a picture of your calipers up... and we might be able to help you id them.

if they are from an r33 gts25t then they would normally have a smooth surface (these are also the same for non-bremb r32 gtr)

r32 gtst will have a ribbed top surface of the caliper

better make sure you know what you have first before getting a vin

EDIT: eh really? what an ass.

when i went in: i just quoted r32 gtst type-m and half a minute later we were printing out the pages, showed him my caliper and we looked at what i needed and how many, how much and when they'd be in brisbane.

NS2500 Experienced

NS2500

Posted
Posted
post a picture of your calipers up... and we might be able to help you id them.

if they are from an r33 gts25t then they would normally have a smooth surface (these are also the same for non-bremb r32 gtr)

r32 gtst will have a ribbed top surface of the caliper

better make sure you know what you have first before getting a vin

They're currently in pieces at the workshop, so they're not handy unfortunately. They're definitely not the the R32 (ribbed) style though.

You've got me on whether they're non-brembo 32R or 33T though - I've noticed there's a slight difference between the two externally but internally - are they the same? ie. seals.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Yea that’s why I said ima test them with multimeter and see the reads.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Only at idle. Isn’t a problem when rev it seems.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...