Jump to content
SAU Community

Recommended Posts

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

for sure dan ya will mate but just got to stick with it... also doing a few efforts as we called them will help ya get ya heart rate up etc.say if ya go for a ride on the weekend where ya dont mind getting smelly,try doing some hard flat out efforts.

how the clip in going?>???

Link to comment
https://www.sau.com.au/forums/topic/148863-cycling/page/3/#findComment-2836802
Share on other sites

little tip-when ya get them ride round the back yard on grass for a little while that way if ya fall you wont hurt u or the bike! practice clipping in and out. its very easy and im sure youll have no troubles with it?

by the way what sort of car you own? never seen any pics of one aye

Link to comment
https://www.sau.com.au/forums/topic/148863-cycling/page/3/#findComment-2838270
Share on other sites

Had a small ride this morning, Innaloo to Hilliarys and back, 23 kms in 62 Minutes... Nice and gentle... Was "Watching" the human ( HOT CHICKS!!!) traffic... Making sure not to be a menace on the cycle path.... Would like to have been on the road, but perving and riding on the road + my luck = Hospital!!!!

Mike

Link to comment
https://www.sau.com.au/forums/topic/148863-cycling/page/3/#findComment-2838707
Share on other sites

bmw nice... mike yeh that could be dangerous,perving+cycling =crash or near crash..and it so annoying when ya fall of scratch ya bike skin of but most of all yhose chicks ya looking at laugh...

Link to comment
https://www.sau.com.au/forums/topic/148863-cycling/page/3/#findComment-2839181
Share on other sites

no way ya joking aint ya???? IF NOT what was you doing wrong,just twist ya heel out ways. maybe the tension is up high mate. just check it out.

hey it happens to most,took me sister out once and she pulled one foot but tried to put the foot still in down haha was so funny

Link to comment
https://www.sau.com.au/forums/topic/148863-cycling/page/3/#findComment-2847310
Share on other sites




  • Similar Content

  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...