Jump to content
SAU Community

Recommended Posts

im selling my direct port nitrous kit complete with lines bottle everything needed to fit comes with a full bottle of gas and is jetted to 108hp 6 cyl kit can be used on 4 cyl and rotor aswell

price $950plus freight

ring jason on 0424348521

how easy are these kits to install?

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2797970
Share on other sites

  • 1 month later...

hi

is this kit sold yet? where are you located?

is it the direct port fittings that sit under each injector or a fogger tapped into the manifold near each cylinder?

thanks

Justin

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2897928
Share on other sites

  • 3 weeks later...

kit comes with 10 pound nitrous bottle

braided main nitrous line

nos solenoid

fuel solenoid

6 seperate direct port foggers with jets

braided lines from solenoids to distribution blocks

and solid lines from distribution block to foggers

kit is complete ready to use

freight will be no probs anywhere in aus or tasmania

new price $800 plus freight

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2938400
Share on other sites

600rwhp 15 psi no gas

the reason for sale is the nos was to get the turbo onto boost with a 4500 rpm stall converter as street registered car ran 9.3 @141mph

the new engine runs a methanol motor with a 5200 rpm stall converter and 2 step so no need for the gas anymore

nos was also used to win dyno comps which im also not interested in anymore

Edited by jas/slo32
Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2950486
Share on other sites

600rwhp 15 psi no gas

the reason for sale is the nos was to get the turbo onto boost with a 4500 rpm stall converter as street registered car ran 9.3 @141mph

the new engine runs a methanol motor with a 5200 rpm stall converter and 2 step so no need for the gas anymore

nos was also used to win dyno comps which im also not interested in anymore

Have left message on your phone and sent pm , please call me - thank you :(

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2953560
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
    • Yes it is ATF. I quote @Duncan "it takes a good synthentic auto trans fluid like Castrol Transmax Z" It's not a diff. It's a transfer case. Totally different thing. Yes, fluid will come out the sender hole. No you do not really need to drain it. Just pull the old, quickly poke the new, clean up and top up. But realistically, you should probably take the opportunity to change it anyway.
    • Hey all. I’m looking on replacing my speed sensor on my R33 GTR. Will the center differential need to be drained, and if so, the center diff uses ATF fluid D? I found information on the transmission, front diff and rear diff. Can’t find a for sure answer for the center diff. Any help will be greatly appreciated.
×
×
  • Create New...