Jump to content
SAU Community

Recommended Posts

Hi,

I was driving back from work the other day and my car was running fine. I was giving a a good burst from time to time then started to notice that the power was progressivly decreasing. By the time I got home I could not boost it over 5psi and at the point it runs realy rich...

I know its rich due to the state of the plugs when I pulled them out to do a compression test, which seemed fine as well (all within 10%).

Things I have done to fix it are:

1) re-fitted all intake piping after the Afm and before the throttle body, there were no obvious leaks.

2) replaced the Z32 AFM with a mates and it made no difference.

I was thinking it could be:

1) crank angle sensor?

2) plenum gasket?

3) maybe a pin hole in the cooler, I have checked and cant see anything?

Any suggestions would be great, I am thinking air leak but its very hard to determine where it might be???

Link to comment
https://www.sau.com.au/forums/topic/149616-possible-air-leak-please-help/
Share on other sites

  • 3 weeks later...

Did you end up sorting this out? I had a very similar problem, and it's turned out to be a plenum gasket for me.

I could actually feel the air rushing out through the giant hole.. I could still get a heap of boost into it though, but it was making a rushing air sound out the side of the plenum when on boost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...