Jump to content
SAU Community

Recommended Posts

Even though i've had my car for a couple months, today was the first time i filled right up. But once i did, and the lever clicked to tell me i was full, i notice petrol dripping from underneath the tank...i was like wtf. No fuel came overflowing from the filler cap. Do the tanks have an overflow thing or something?? : So i then turned the car on and after a about 5 minutes the dripping eased up. What could be wrong with the tank? split? The car is R32 GTS-t.

Any help appreciated,

Scott

Link to comment
https://www.sau.com.au/forums/topic/14971-first-time-fill-tank-up/
Share on other sites

It could also, and most probably be, a f@rked seal on the tank. It is not normal for the petrol to drip out for 5 min. on the floor, not to mention dangerous. Hate to make you feel bad but better be safe than sorry.

When i got my company van (already 3yrs old, from new) i noticed that after filling the tank, to full, petrol would drip out the bottom. I decided to have a look one day and got on the floor, while at the station. The petrol wasn't coming out of a 'over flow pipe' and the leak appeared to start up high (out of sight). Told my boss to book it in for a check. The MERC. dealership was surprised to find the seal stuffed, especially on a 3yr old van.

Sorry about the story but just speaking from experience.

PS: if your seals are stuffed (due to the car's age) vapours can be escaping out of the tank, thus you are loosing petrol. NOT TO MENTION THAT VAPOURS ARE THE MOST LIKELY CAUSE OF A PETROL EXPLOSSION. For your safety i would get it checked out properly, by asking your mechanic to remove the tank and inspect it.

My 2c

Alan

actually the first time i filled my car up, it kept clicking like every litre, so what happend as i was filling it up and i let it click one to many times and the petrol splashed up my hand and down my leg.

i have found that if you don't put the nozzle right it it doesn't click as often :(

not related but hey :)

Originally posted by a5h

actually the first time i filled my car up, it kept clicking like every litre, so what happend as i was filling it up and i let it click one to many times and the petrol splashed up my hand and down my leg.

try another servo....I've had the same thing happen at certain servo's, takes bloody ages to fill up the car :mad: but at other servo's it's fine. So I just avoid the ones that keep clicking off now :)

I fill up at the same station, same bowser every week. I fill it until it clicks and then just slowly fill it until i reach even dolars (usually another 0.5-1.0 Litres).

In the end its around 60ish Litres.

Find a good pump and stick to it is my theory.

I've found out that there is a problem with my tank, cuz i got someone to tail me on the road and whenever i turned sharply, fuel would piss out from somewhere. The only thing i've got done to the car around the tank area was installed a high flow pump. Could it just be the seal around near the filler cap?

Regards,

Scott.

Now it looks like i've spoted the problem...and an easy one to fix. I took off the plastic inner guard on the rear left wheel and discover that the breather pipe had come off the connection to the inside of the filler cap. It's got me ****ed on how it came off...

Scott.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...