Jump to content
SAU Community

Where Can I Get Rb25 Timing Belt Parts?

abcent

By abcent,
in General Maintenance

 Share

Recommended Posts

abcent Mentor

abcent

Posted
Posted

I already got myself a gates racing timing belt, cant believe there cheaper than a standard one....strange.

After ringing around a few places, it seems there is no aftermarket pulleys (eg: gates), an my local Nissan dealer are useless on there import stuff an cant seem to find them. Has anyone bought the Idler an Tensioner pulleys new? If so, where from? what sort of cost were they? did they come with new bolts?

Any help is much appretiated!

Berin

DVS JEZ Grand Master

DVS JEZ

Posted
Posted
several places in sydney shud have them. best bet is justjap

nissan charge over the roof for the tensioner and the idler,

take your old ones to a bearing place and they can press in some new bearings cheap as.

Godzilla32 Veteran

Godzilla32

Posted
Posted (edited)

Already covered many times. BSC sell new aftermarket ones complete. From memory it was no more than $120 for both.

Deren

BTW: The gates T-belt is cheaper bacause its non-genuine.

Edited by Godzilla32
abcent Mentor

abcent

Posted
  • Author
Posted
BTW: The gates T-belt is cheaper bacause its non-genuine.

I mean the gates RACING (blue) timing belt is cheaper than the gates standard belt. only cost me $89 :), the gates standard one was going to cost $130-$140 from memory

I like the idea of getting new bearings pressed in, probably the cheapest, but I want to change the belt in one arvo.

Deren: sorry if this has been covered heaps, i tend to steer clear of the search option as you end up sifting through a million pages of irrelevant stuff.

Who are BSC? do these ones come with new bolts?

thanks again

Im in Victoria..so am unaware of the "several" places in Sydney that should have them. Not even sure where to start looking in Melbourne :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      GTR R34 Limp Mode

      By GTSBoy · Posted

      Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • steven7270
      GTR R34 Limp Mode

      By steven7270 · Posted

      So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Dose Pipe Sutututu
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Dose Pipe Sutututu · Posted

      Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...