Jump to content
SAU Community

Recommended Posts

Hi there peoples have a problem not sure if i have detonation or a misfire been having excessive blow by but its been doing that since i had a track day didnt have a problem with pinging or misefire if thats what it is. as soon as full boost hits its wierd sound in one sense it sounds like misfire and then it sounds a jar of ball bearings rattling can some one shed some light on issue >_<

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/
Share on other sites

Hi there peoples have a problem not sure if i have detonation or a misfire been having excessive blow by but its been doing that since i had a track day didnt have a problem with pinging or misefire if thats what it is. as soon as full boost hits its wierd sound in one sense it sounds like misfire and then it sounds a jar of ball bearings rattling can some one shed some light on issue >_<

the jar of ball bearings i would guess is pingin gor detonating. Thats very bad. Id consider lowering the boost and make sure u run high octane petrol. If that doesnt minise it try taking timing out. Realyl ur best option is to go to a reputable skyline tuner and have it cheacked.

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2805950
Share on other sites

What mods? What boost? What fuel?

Mods are engine rebuilt arias pistons shotpenned rods fully balanced

microtech

sard 850cc injectors

hks cams 256 264

hks to4z

eboost settings at 17 20 25 psi

running mobile 8000 with 104 octane booster

never had detonation before on all three boost settings

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2808988
Share on other sites

take it to a dyno and get them to put a fuel pressure tester on and do a power test to see whats going on.

If you dont you will blow your engine to pieces.

BTW if you have blow by allready then you could have smashed some rings. do a leak down test.

my engine had lots of blow by and when i pulled it down 5 pistons had cracked / broken rings

Edited by Guilt-Toy
Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2809646
Share on other sites

take it to a dyno and get them to put a fuel pressure tester on and do a power test to see whats going on.

If you dont you will blow your engine to pieces.

BTW if you have blow by allready then you could have smashed some rings. do a leak down test.

my engine had lots of blow by and when i pulled it down 5 pistons had cracked / broken rings

Had a leak down test three weeks ago all cylinders except for two were at 15% the other two were at 55 60%

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2809667
Share on other sites

Old chestnut as they say but..........fuel pump failing?

Det is from running too lean, timing to far advanced or carbon hotspots on the pistons [igniting fuel before your sparkplug does].

when i had it dynoed the fuel pump was maxing out took the fuel return line off nothing was going back that was at 25 psi

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2809673
Share on other sites

looks like those cyl are leaking boost into the sump causing the blow by.

id look at re-ringing it and checking the pistons.

Ill be doing that in next few weeks pulling engine out putting total seal iron rings good for hi boost apparently changing rods to to argo rods get them real cheap $800 new replace bearings probably acl and get head flow tested and ported to suit the flow of hks t04z then change to surge tank and dual fuel pumps.

If all goes well hope to crack 400 rwkw fingers crossed

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2809854
Share on other sites

Ill be doing that in next few weeks pulling engine out putting total seal iron rings good for hi boost apparently changing rods to to argo rods get them real cheap $800 new replace bearings probably acl and get head flow tested and ported to suit the flow of hks t04z then change to surge tank and dual fuel pumps.

If all goes well hope to crack 400 rwkw fingers crossed

sounds like a good setup. make sure ya let us no how ya go

Link to comment
https://www.sau.com.au/forums/topic/150764-need-advice/#findComment-2809889
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...