Jump to content
SAU Community

Anyone With Split Fires For S2 R33, Urgent

WogsRus

By WogsRus,
in Engines & Forced Induction

 Share

Recommended Posts

WogsRus Veteran

WogsRus

Posted
Posted

HI

Anyone with a S2 R33 and splitfires, WITH A MULTIMETER, got to their splitfire coils and do a resistance reading between the ground, center plug and the LH one when looking at the coil, for the coil. ALSO tell me what the mulitmeter was set at? i have 20, 200, 2000, 20k, 200k, and 2000k ohms.

I tested mine and i get 1600ohms, when the mulitmeter is set to 2000ohm reading. The AUTO electritian told me it has to be 0.9 ohms, and that is near imposible.

This is to do with my other thread, i can't seam to fix my car. http://www.skylinesaustralia.com/forums/in...howtopic=151261

heller44 Mentor

heller44

Posted
Posted (edited)

Because you have a series 2, the coils on your car differ greatly from an older car's coil. Yours has the transistor drive built into the coil package, whereas the earlier engines had a seperate transistor pack.

On the older, seperate transistor, coil engines the reading on the primary side should be about 0.9Ω.

On your car you are trying to read through the transistor as well as the coil winding, so your reading will be a lot different.

Use your diode test on your meter, and go between pins 1 and 2, both ways round. Compare the reading you get with the other 5 coils. See wether there is a variation between the set.

Hope that helps at all.

James.

Edited by heller44
  • 1 year later...
Ultimategtr Proficient

Ultimategtr

Posted
Posted

Sorry to dig up an old thread like this but i am also keen on knowing this!

I have a similar problem. I just want to know whether the reading should be between .6-.9ohms.. can anyone confirm??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      Stagea Front CV Axle Question

      By dbm7 · Posted

      Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
×
×
  • Create New...