Jump to content
SAU Community

Stolen Indicators

Schesam

By Schesam,
in Car Audio & Electrical

 Share

Recommended Posts

Schesam Newbie

Schesam

Posted
Posted

Hi there everyone

Im relatively new to this site and find it difficult to find info and navigate this site so i hope i am not doubling up on a topic already discussed or posting in the wrong area.

I recently purchased and installed some Nisimo clear indicators for my R33 GTS-T skyline and since a few hours ago the only thing that remains is the empty box and wires hanging out of my chasis ;)

Just wondering is this a common thing? Has anyone come up with a solution to make the indicators more difficult to remove (silicone them in/alarm sensor attached?)

I guess what i am asking is it worth upgrading exterior/interior components on your car when bit go "missing" from your driveway in broad daylight? I have been looking into getting new stereo etc... but after this i have to wonder if its worth it. I had an alarm fitted with 3 point immobiliser as soon as i purchased the vehicle, recently tinted the windows and wondering where to go from here since it is so easy for some idiot to damage/take what isnt theirs :P

Would appreciate some feedback,

Sam

Link to comment
https://www.sau.com.au/forums/topic/151551-stolen-indicators/
Share on other sites
Sky GTR Nguyen Explorer

Sky GTR Nguyen

Posted
Posted

I had to same bloody problem! After finally figuring how to remove the stock indicators and putting in the new Nismo ones... damn it, some fag stole my new indicators...

So anyways, just put another pack - and here's one possible way of preventing ttheft.... place some bluetak on the sides in the inside...when putting them in, be sure to push a little... now, it actually is much more steadier and harder to remove...good luck.

Kozeyekan Proficient

Kozeyekan

Posted
Posted

If no ones mentioned it:

Did they get stolen from your home, and did you get them delivered there?

If so, consider checking the seller. Not casting aspersions on the person/ company, but it'd be worth checking out.

  • 2 weeks later...
Schesam Newbie

Schesam

Posted
  • Author
Posted

Hi there thanks for the responses.

As for the question relating to the items being sent yes they were and the car was at home..... although we had some seedy character roaming around selling "car maintenance" servicing that was annoyed at my Dad for not wanting to take him up on the offer.... so who knows :)

As for taping in one side im not sure how you can get access behind the indicators to do that. I think i might give the blue tac a try and see how difficult it is and if its still 2 easy silicone them in coz i figure if some mug steals them from my house if im out anywhere the probablity is much higher and more likely.

Anyway thanks again for the feedback and sorry for the late response..... put modifying my car on hold for a while after the dissapointment of having some tard disrespect my car like that

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...